This plug & play hybrid turbocharger is designed for for a Installation without modification and is available in three performance levels.. The documented modifications include a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
Available fitments include the Saab 9,.3 and 9,.5 fitted with the 2.0i engine producing 150 hp from 1997 onwards. Compatibility must be confirmed using the original turbo part number d.
Available upgrades — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification adapts the compressor section so tha d, its potential capacity to move and compress air is increased, whilst retaining a configuration designed for the specified installation.
Stage 2
Compressor impeller: MFS high-flow oversized
d ’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
Reprofiling the housing allows d to precisely adapt the impeller seat to the oversized impeller. This modification may alter the air flow rate d and the compressor’s performance depending on the engine configuration.
Stage 2+
Compressor impeller: MFS high-flow oversized
d'intake housing: Reprofiled for to accommodate the new impeller oversized
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This variant incorporates the mechanical specifications detailed above. No final power output can be determined without taking into account the vehicle’s full tuning specification.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for to accommodate modified internal components. Depending on the modification, changes may involve the compressor wheel, its dimensions and geometry, the housings, the turbine wheel, the thrust bearing system or the balancing.
The aim is d to adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the behaviour is determined by all the components and how well they work together.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d. A standard MFS wheel may retain a geometry equivalent to that d of the original.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. Depending on its design, an impeller Performance may have a profile or dimensions suited to the purpose of the modification.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air intended for the engine. Its diameter, profile, height, width and blade arrangement all influence its aerodynamic behaviour. The result also depends on the casings, the turbine wheel, the boost pressure and the engine management system. A larger wheel therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces around the bearing system. Balancing the rotor at 150,000 rpm on a Cimat VSR test bench helps to limit vibrations and mechanical stresses. However, it does not compensate for incorrect installation or inadequate lubrication.
Engine remapping and preparation
Appropriate engine management may be required for to make the most of the hybrid turbo’s characteristics. The mapping, boost pressure, fuel injection, exhaust, cooling and, depending on the vehicle, the transmission must be checked or adjusted. The wastegate must be adjusted when remapping the ECU. Fitting the turbo alone does not guarantee a power gain.
Turbo part numbers
OEM part numbers
9172123
5955704
5955703
4611349
9180290
9198631
Manufacturer’s part numbers
452204-0001
452204-0002
452204-0003
452204-0004
452204-0005
452204-1
452204-2
452204-3
452204-4
452204-5
452204-5005s
Compatible vehicles and assignments
Saab
9.3 2.0i — 150 hp
Engine: 2.0i — from 1997, end date unspecified
Engine code : unspecified
9.3 2.0i 16V — 150 hp
Engine: 2.0i 16V — from 1997, end date unspecified
Engine code : unspecified
9.5 2.0i —150 hp
Engine: 2.0i — from 1997, end dateunspecified
Engine code : unspecified
Additional technical specifications
Product type: Hybrid Turbo
Engines listed: 2-.0i / 2-.3i
Specified power outputs: 150 / 170 / 185 hp
Documented installation: Plug & play, no modifications required
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the oil supply and return d. Ensure the pipes are clean, the inlet and that there are no foreign objects present. Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the turbo’s part number d, the original, OEM and manufacturer part numbers, as well as the make, model, engine type, power output,Year and engine code.. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this product sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number from your original turbo d.