This hybrid turbo for engines 1.6 TDI is designed for for installation Installation without modification. Its internal modification is aimed at adjusting the compression ratio and air flow d, without specifying the final power output, which depends on the engine configuration and its electronic control system.
Available tuning options — Stage 1, Stage 2 and Stage 2+
Stage 1: high-flow MFS compressor impeller, 360° bearing stop and high-speed balancing at 150,000 rpm on a Cimat VSR test bench.
Stage 2: high-flow MFS compressor impeller oversized, d’s re-profiled inlet casing for to accommodate this impeller, 360° stop and balancing at 150,000 rpm on a Cimat VSR test bench.
Stage 2+: high-flow MFS compressor impeller oversized, d’s re-profiled intake housing, 360° thrust bearing and balanced at 150,000 rpm on a Cimat VSR test bench. No other mechanical differences are specified in the available data.
Hybrid turbo technology
MFS stands for ‘Milled From Solid’, meaning aturbine wheel machined from a solid block. A standard MFS turbine wheel can be just as shiny as an MFS turbine wheel Performance: it is not its appearance that determines its performance, but its geometry and its ability to move more d’air. The diameter, profile, height, width and blade arrangement all influence the compressor’s aerodynamic behaviour. However, a oversized impeller does not automatically guarantee better performance and may alter the response time. The 360° thrust bearing distributes axial forces, whilst rotor balancing helps to limit vibrations and mechanical stresses. Appropriate mapping, as well as control of fuel injection, exhaust, cooling and boost pressure, are required for to make the most of the upgrade.
Turbo part numbers
OEM:
03L253016AX
03L253016A
03L253016HV
03L253016HX
03L253016H
03L253056DX
03L253056D
03L253056RX
03L253056R
Manufacturer:
54399700086
54399880086
54399700094
54399880094
54399700098
54399880098
54399700114
54399880114
54399700136
54399880136
Compatible vehicles and specifications
Audi : A1 (8X1, 8XK), 90 hp CAYB from 03/2011 to 04/2015 and 105 hp CAYC from 05/2010 to 04/2015; A1 Sportback (8XA, 8XF), 90 hp CAYB and 105 hp CAYC from November 2011 to April 2015.
Seat : Ibiza IV (6J5, 6P1), 90 hp CAYB and 105 hp CAYC/CLNA from May 2009 to May 2015; Ibiza IV SC (6J1, 6P5), 90 hp CAYB and 105 hp CAYC from May 2009 to May 2015; Ibiza IV ST (6J8, 6P8), 90, hp, CAYB and 105, hp, CAYC/CLNA from March 2010 to May 2015; Toledo, 90, hp, CAYB from November 2007 to December 2007; Toledo, 90, hp, CASA/CASC from November 2007 to December 2007; Toledo IV (KG3), 90, hp, CAYB from June 2013 to June2015.,
,Skoda: Fabia II (542), 90 hp CAYB and 105 hp CAYC from March 2010 to December 2014, as well as 75 hp CAYA from April 2010 to December 2014; Fabia II Combi (545), 90, hp CAYB and 105, hp CAYC from March 2010 to December 2014, as well as 75, hp CAYA from April 2010 to December 2014; Rapid (NH3, NK3, NK6), 105 hp CAYC/CLNA from July 2012 to December 2019; Roomster (5J7), 75 hp CFWA, 90 hp CAYB and 105 hp CAYC from March 2010 to May 2015; Roomster Praktik (5J), 90 hp CAYB from March 2010 to May 2015.
Volkswagen: Polo V (6R1, 6C1), 75 hp CAYA, 90 hp CAYB and 105 hp CAYC/CLNA from 06/2009, end date unspecified.
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the circuit, the supply and return lines dthe oil, the cleanliness of the pipes, the intake and the absence of foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further damage to the turbocharger.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original dturbo with the part numbers listed in this data sheet. An identical engine type does not always guarantee compatibility.