This hybrid turbo for engine 1.4 TDI 75 hp offers three distinct levels of preparation. Each configuration uses a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing on a Cimat VSR bench.
The documented assignments relate in particular to Audi A2, SEAT Arosa, Córdoba and Ibiza, Skoda Fabia and Volkswagen Lupo and Polo models fitted with the engine codes listed in this specification sheet.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: High-capacity MFS
Dimensions: 31.08 / 44.01 mm
Blade configuration: 6+6
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This design is based on an MFS impeller with a high-flow geometry. It aims to adjust travel capacity d'air whilst retaining a configuration that is less oversized than the other two courses.
Stage 2
Compressor wheel: High-capacity MFS oversized
Dimensions: 36.30 / 49.00 mm
Blade configuration: 11+0
Carter d'Admission:' reprofiled for to receive the new wheel
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The larger diameter requires the casing to be re-profiled d'admission'. This combination may increase flow capacity, but its operation depends on the engine management system and the overall mechanical configuration.
Stage 2+
Compressor wheel: High-capacity MFS oversized
Dimensions: 38.62 / 52.19 mm
Blade configuration: 11+0
Carter d'Admission:' reprofiled for to receive the new wheel
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This version has the largest wheel of the three documented configurations. Such a change may affect the available flow rate, response time and optimal operating range; it must therefore be selected in accordance with the motor design.
What is a hybrid turbo ?
A hybrid turbo utilises a turbocharger design that has been adapted to accommodate modified internal components. Depending on the specific design, modifications may relate to the compressor impeller, its geometry, its dimensions, the casings, the turbine impeller, the thrust bearing system or the balancing.
The aim is d'adjust the compression capacity and flow rate' d'air'. However, a hybrid turbo is not defined solely by the appearance of its impeller: the dimensions, geometry and overall balance are crucial.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in throughput d'air'. A standard MFS wheel can retain a geometry equivalent to that d'origin'.
An MFS wheel Performance can be designed with a geometry suited to the intended application: specific blade profile, dimensions or configuration, depending on the available technical data. A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air'.
A higher flow rate can help to increase power output when the engine management system and peripheral equipment are correctly configured, although this does not in itself guarantee a gain in power.
Why does the geometry of the blades affect the flow rate? d'air?' ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades all influence its aerodynamic behaviour. The right geometry can move more d'air under certain operating conditions'.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine tuning. A larger wheel therefore does not automatically lead to a better result and may affect the response time.
Reliability and balancing of the hybrid turbocharger
The 360° stop, documented in each stage, helps to distribute the axial forces within the turbocharger. Rotor balancing minimises vibrations and mechanical stresses at very high speeds.
All three configurations are balanced at 150,000 rpm on a Cimat VSR test bench. However, this balancing does not compensate for incorrect installation, insufficient lubrication or the presence of foreign objects.
Engine remapping and tuning
It may be necessary to adjust the mapping and management of boost pressure for make the most of the hybrid turbo’s features. The wastegate must be adjusted during the installation and remapping of the ECU.
Depending on the level of preparation, it is also advisable to check whether or d'adjust the fuel injection, exhaust and air cooling' d'the intake, the clutch and the transmission'. The editing d'A hybrid turbo does not automatically deliver a performance gain without appropriate engine tuning'.
Turbo part numbers
OEM part numbers
045145701
045145701C
045145701CV
045145701CX
045145701J
045145701JX
045145701V
045145701V400
045145701V405
045145701V500
045145701X
Manufacturer’s part numbers
701729-0001
701729-0003
701729-0006
701729-0009
701729-0010
701729-1
701729-10
701729-2010
701729-3
701729-5009S
701729-5010S
701729-6
701729-9
706680-0001
706680-1
706680-2001
706680-5001S
Compatible vehicles and assignments
AUDI
A2 (8Z0) — 75 hp
1.4 TDI diesel — February 2000 to August 2005
Engine codes: AMF, BHC
SEAT
Arosa (6H1) — 75 hp
1.4 TDI diesel — Jan 2000 to Jun 2004
Engine code : AMF
Córdoba (6L2) — 75 hp
1.4 TDI diesel — October 2002 to December 2005
Engine code : AMF
Ibiza III (6L1) — 75 hp
1.4 TDI diesel — May 2002 to December 2005
Engine code : AMF
Skoda
Fabia I Praktik (6Y5), light commercial vehicle — 75 hp
1.4 TDI diesel — August 2004 to October 2005
Engine code : AMF
Volkswagen
Lupo I (6X1, 6E1) — 75 hp
1.4 TDI diesel — January 1999 to July 2005
Engine code : AMF
Polo (6N2) — 75 hp
1.4 TDI diesel — October 1999 to September 2001
Engine code : AMF
Polo (9N_, 9A_) — 75 hp
1.4 TDI diesel — October 2001 to June 2005
Engine codes: AMF, BAY
Additional technical specifications
Product type: hybrid turbo
Engine: 1.4 TDI
Fuel: diesel
Power : 75 hp
Engine codes: AMF, BAY, BHC
Period covered: Jan 1999 to Aug 2005, depending on the vehicle
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Identify and rectify the cause of the previous fault before d'fit the turbo'.
Check the lubrication circuit, the supply and the return d'the oil and the cleanliness of all the pipes'. Also check the intake and ensure there are no foreign objects present.
Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions. Wastegate adjustment and mapping should be carried out by a qualified professional.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number engraved on the turbocharger d'origin', then compare the OEM and manufacturer part numbers. Also check the make, model, generation, body style, engine type and power output of 75 hp, the installation dates and the engine code.
Having the same engine is not always enough to confirm compatibility, as there may be several different configurations within the same range of vehicles.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d'origin' using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are unsure about which service package to choose, please contact us with the full reference number for your turbocharger d'origin'.