This hybrid turbo for engine variants 1.8 i is available in three documented levels of preparation. Depending on the course chosen, he receives an MFS compressor wheel Performance and, for the oversized versions, a casing d’re-profiled intake to d’to accommodate the new wheel’.
It is designed for a range of applications Audi, , Seat, , Skoda and Volkswagen producing 150, 180 or 225 hp. Its design is planned for one Installation without modification external, subject to a thorough check of the installation’s specifications d’origin’.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS Performance high-speed
Documented dimensions: 32.94/49.00 mm and 38.10/50.96 mm
Blade configuration: 4+4
Stop: 360°
Balancing: high speed at 150,000 revolutions per minute on a Cimat VSR test bench
This preparation is based on an MFS wheel Performance with documented geometry for adjust the flow rate dair. The final performance also depends on the engine management system and all the associated components.
Stage 2
Compressor wheel: MFS Performance high-speed oversized
Documented dimensions: 42.00/56.08 mm
Blade configuration: 11+0
Carter d’Admission:’ reprofiled for to accommodate the wheel oversized
Stop: 360°
Balancing: high speed at 150,000 revolutions per minute on a Cimat VSR test bench
The wheel oversized and the re-profiling of the casing d’The intake valves are designed to adjust the compression ratio and flow rate’ dair. This change may also alter the turbocharger’s response, depending on the engine configuration.
Stage 2+
Compressor wheel: MFS Performance high-speed oversized
Documented dimensions: 50.07/62.43 mm
Blade configuration: 7+7
Carter d’Admission:’ reprofiled for to accommodate the wheel oversized
Stop: 360°
Balancing: high speed at 150,000 revolutions per minute on a Cimat VSR test bench
This version uses a larger impeller with a specific blade configuration. Using it requires careful preparation; a larger wheel size alone does not guarantee a better result in all conditions.
What is a hybrid turbo ?
A hybrid turbo is based on a specially adapted turbocharger design for to receive internal changes. Depending on the specific application, these may relate to the compressor wheel, its geometry, its dimensions, the machining of the casings, the thrust bearing or the balancing.
The aim is d’adjust the compression capacity and flow rate’ dair. However, a hybrid turbo is not defined solely by the appearance of its impeller: its aerodynamic characteristics, dimensions and the overall coherence of the unit are crucial.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process does not, on its own, guarantee an increase in throughput dair. A standard MFS wheel can retain a geometry equivalent to that d’origin’.
An MFS wheel Performance may adopt a geometry suited to the intended purpose, in particular a specific profile, diameter or blade configuration, where these elements are documented.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. A higher flow rate can help to generate more power with the appropriate engine tuning, although this does not in itself guarantee a performance gain.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air intended for the engine. Its diameter, profile, height, width and the arrangement of the blades influence its aerodynamic behaviour and the amount d’air displaced under certain operating conditions’.
The result also depends on the compressor housing, the turbine section, the boost pressure and the engine tuning. A larger wheel does not automatically guarantee better performance and may affect response time and range doptimal use.
Reliability and balancing of the hybrid turbocharger
All three preparations contain da 360° stop, designed for distribute the axial forces around the joint. This provision does not exempt d’proper lubrication nor d’a compliant installation’.
The rotor is balanced at high speed – 150,000 revolutions per minute – on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not protect against a lack of lubrication; the presence da foreign object or incorrect installation.
Engine remapping and tuning
It may be necessary to adjust the engine management system for make the most of the hybrid turbo’s features. Mapping, boost pressure and wastegate settings must be checked and adjusted during installation and remapping.
Depending on the level of preparation: fuel injection, fuel supply, exhaust system, air cooling d’The intake system, the clutch or the gearbox may also need to be checked or adjusted. A hybrid turbo does not automatically guarantee a performance gain without appropriate engine tuning.
Turbo part numbers
OEM part numbers
06A145713D
06A145704S
06A145704SX
06A145704SV
06A145713B
06A145713BX
06A145713BV
06A145713F
06A145713FV
06A145713FX
06A145713DV
06A145713L
06A145713LV
06A145713LX
06A145713M
06A145713MX
06A145713MV
06A145713DX
06A145713N
06A145713NV
06A145713NX
06A145704T
06A145704TV
06A145704TX
06A145702P
06A145702PX
06A145702PV
Manufacturer’s part numbers
53039700052
53039700053
53039700058
53039700094
53039880052
53039880053
53039880058
53039880094
Compatible vehicles and assignments
Audi
A3 Series 1 — 1.8 i — 150 hp
From 1996, month and end date unspecified
Engine code : not specified
TT — 1.8 i — 150 hp
From 1998, month and end date unspecified
Engine code : not specified
TT — 1.8 i — 180 hp
From 1998, month and end date unspecified
Engine code : not specified
TT — 1.8 i — 225 hp
From 1998, month and end date unspecified
Engine code : not specified
Seat
Ibiza 3–1.8 i — 180 hp
From 2004, month and end date unspecified
Engine code : not specified
Leon — 1.8 i — 180 hp
From 1999, month and end date unspecified
Engine code : not specified
Toledo — 1.8 i — 180 hp
From 2003, month and end date unspecified
Engine code : not specified
Skoda
Octavia — 1.8 i — 150 hp
From 1996, month and end date unspecified
Engine code : not specified
Volkswagen
Bora — 1.8 i — 180 hp
From 1999, month and end date unspecified
Engine code : not specified
Golf 4 — 1.8 i — 180 hp
From 1997, month and end date unspecified
Engine code : not specified
Jetta — 1.8 i — 180 hp
From 2002, month and end date unspecified
Engine code : not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 1.8 i
Application capabilities: 150, 180 and 225 hp
Documented periods: from 1996 onwards, depending on allocation
Engine codes: not specified
Installation: designed without any external modifications, subject to compatibility
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Identify and rectify the cause of the previous fault. Check the lubrication circuit, the supply and the return doil, as well as ensuring that all ducts are clean.
Check the intake and ensure there are no foreign objects. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions. The wastegate setting and engine management must be adjusted during installation and remapping.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the turbo part number dCheck the part number and compare it with the OEM and manufacturer part numbers listed in this data sheet. Also check the make, model, generation, engine type and power output in hp, theYear installation details and, where available, the engine code. Having the same motor does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact us, quoting the reference number clearly visible on your turbocharger d’origin’.