This hybrid turbo for engine variants 1.9 TDI offers in-house programmes tailored to different objectives. The three levels on offer all use an MFS compressor wheel Performance, a 360° bearing stop and high-speed balancing on a Cimat VSR test bench.
The documented assignments relate in particular to certain Audi A4 and A6, Skoda Superb and Volkswagen Passat. The benchmark for turbochargers dThe origin must be verified before any order is placed.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS Performance high-speed
Dimensions: 32.94 / 49.00 mm
Blade configuration: 6+6
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This preparation acts primarily on the compressor wheel in order to d’adjust the travel capacity’ d’air, whilst retaining the characteristics specific to this level of preparation.
Stage 2
Compressor wheel: MFS Performance high-speed oversized
Dimensions: 36.77 / 52.19 mm
Blade configuration: 11+0
Carter d’Admission:’ re-profiled for to receive the wheel oversized
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The wheel with the larger diameter is fitted here d’a re-profiling of the casing d’admission’. This assembly is designed to alter the compression capacity and flow rate d’air under the conditions specified in the preparation.
Stage 2+
Compressor wheel: MFS Performance high-speed oversized
Dimensions: 39.61 / 56.02 mm
Blade configuration: 11+0
Carter d’Admission:’ re-profiled for to receive the wheel oversized
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This stage uses the largest compressor wheel of the three documented configurations. An increase in size may affect the potential flow rate, response time and range d’Optimal use of the turbocharger’.
What is a hybrid turbo ?
A hybrid turbo is based on a specially adapted turbocharger design for to receive internal components or machined parts that differ from the specification d’origin’. Depending on the modification, changes may relate to the compressor impeller, its dimensions, the geometry of the blades, the casings, the turbine impeller, the thrust bearing or the balancing.
The aim is d’adjust the compression capacity and flow rate’ dair. A hybrid turbocharger is therefore not defined solely by the appearance of its compressor wheel: the coherence of the mechanical assembly as a whole and its integration with the engine management system are essential.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This term describes a manufacturing process and, on its own, is not sufficient to establish an increase in throughput dair.
A standard MFS wheel can retain a geometry equivalent to that d’origin’. An MFS wheel Performance may have a specific blade profile, diameter or configuration tailored to the preparation objective, such as the documented dimensions and configurations for the three stages of this product.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. A higher flow rate can enable the engine to produce more power when combined with a correctly sized engine upgrade.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the amount dthe volume of air it can displace under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine tuning. A larger wheel is not necessarily suitable for all uses and may affect the turbo’s response time.
Reliability and balancing of the hybrid turbocharger
The 360° stop fitted to each stage distributes the axial forces around the axis. It helps to adapt the bearing to the stresses of the preparation process, without replacing proper lubrication or correct assembly.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This procedure is designed to minimise vibrations and mechanical stresses, but does not compensate for a fault doil supply, contamination or incorrect installation.
Engine remapping and tuning
The engine mapping and boost pressure control need to be adjusted for make the most of the hybrid turbo’s features. Depending on the level of preparation, injection, fuel supply and air cooling dThe intake, exhaust, clutch or transmission must also be checked or adjusted. The wastegate must be adjusted during installation and when the ECU is reprogrammed.
Turbo part numbers
OEM part numbers
028145702A
028145702AV
028145702AX
028145702H
028145702HV
028145702HV225
028145702HV500
028145702HX
038145702H
038145702HV
038145702HX
038145702K
038145702KV
038145702KX
038145702LX
Manufacturer’s part numbers
454231-0001
454231-0003
454231-0004
454231-0005
454231-0007
454231-1
454231-3
454231-4
454231-5
454231-5007S
454231-7
761437-0001
761437-0003
761437-0005
761437-1
761437-3
761437-5
Compatible vehicles and assignments
Audi
A4 Pre-Series 1 Phase 2 — 115 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
A4 Pre-Series 2 — 100 / 116 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
A4 Pre-Series 2 Phase 2 — 116 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
A4 Series 2 — 100 / 116 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
A4 Series 2 Phase 2 — 116 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
A6 — 100 / 110 / 115 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
Skoda
Superb — 105 / 115 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
Volkswagen
Passat B4 — 115 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
Passat B5 — 100 hp
1.9 TDI — from 1998, end date unspecified
Engine code : not specified
Additional technical specifications
Product type: hybrid turbo
Engine: 1.9 TDI
displacement : 1.9 L
Period covered: from 1998, end date unspecified
Engine codes: not specified
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLYBefore installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the supply and return lines doil. Check that the ducts and the intake are clean and free from foreign objects. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions.
Engine management, boost pressure and wastegate settings must be adjusted to suit the selected tuning package. If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number engraved or marked on the turbocharger dthe original, then compare it with the OEM and manufacturer’s part numbers listed on this sheet. Also check the make, model, generation, body style, engine type and power output in hp, the assembly period and the engine code, where available.
⚠️ Check your turbo’s part numbersBefore placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact us with the full reference number of your turbocharger dVehicle origin and details.