This hybrid turbo for 2.7 and 3.0 engine sizes TDI is based on a configuration plug & play and receives in-house training tailored to the selected course. The three documented variants all feature an MFS compressor wheel Performance, a 360° bearing stop and high-speed balancing.
The assignments cover, in particular, several Audi A4, A6, A8 and Q7, as well as the Volkswagen Phaeton and Touareg. The benchmark for turbochargers dThe origin, engine code and date of manufacture must be checked before placing any order.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: High-capacity MFS Performance
Dimensions: 43.03 / 56.08 mm
Blade configuration: 6+6
Stop: 360° bearing
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This configuration uses an MFS wheel Performance designed to regulate the flow rate d’compressor air, whilst maintaining an installation with no documented external modifications’. Its ultimate performance depends on the engine management system and the overall mechanical configuration.
Stage 2
Compressor wheel: High-capacity MFS oversized Performance
Dimensions: 46.39 / 60.00 mm
Blade configuration: 7+7
Carter d’Admission:’ re-profiled for to receive the wheel oversized
Stop: 360° bearing
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The wheel oversized and the re-profiling of the casing d’Admission modifications affect the vehicle’s range’ dcompressor air. This change may also affect the response time and must be taken into account by means of appropriate calibration.
Stage 2+
Compressor wheel: High-capacity MFS oversized Performance
Dimensions: 54.20 / 66.56 mm
Blade configuration: 6+6
Carter d’Admission:’ re-profiled for to receive the wheel oversized
Stop: 360° bearing
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This variant uses the largest documented wheel for this product and a casing d’an inlet suited to its dimensions’. A larger size alone does not guarantee better performance in all conditions: the outcome depends on the engine being fully prepared.
What is a hybrid turbo ?
A hybrid turbo retains a turbocharger design that is suitable for accommodating modified internal components. Depending on the design, these modifications may relate to the compressor impeller, its dimensions, the geometry of the blades, the casings, the turbine impeller, the thrust bearing or the balancing.
The aim is d’adjust the compression capacity and flow rate’ dair. A hybrid turbo is therefore not defined solely by the appearance of its impeller: consistency between the components and the quality of their fit are essential.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This term describes a manufacturing process and does not, in itself, guarantee an increase in throughput dair.
A standard MFS wheel can retain a geometry equivalent to that d’origin’. An MFS wheel Performance may, where the technical specifications so provide, adopt a blade profile, diameter or configuration suited to the purpose of the preparation.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. A higher flow rate can help to generate more power only if the engine has been properly tuned.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the amount dthe volume of air it can displace under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine calibration. A larger wheel may affect response time and range doptimal use; it therefore does not automatically guarantee a better result.
Reliability and balancing of the hybrid turbocharger
The 360° stop, documented for each stage, helps to distribute the axial forces borne by the rotating assembly. However, it does not exempt one from d’proper lubrication nor d’a compliant installation’.
The rotor is balanced at high speed – 150,000 rpm – on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not protect against a fault dthe oil supply, the presence da foreign object or incorrect installation.
Engine remapping and tuning
The mapping and management of boost pressure need to be adjusted for make the most of the features da hybrid turbo. Depending on the level of preparation, the fuel supply and the air cooling d’The intake, exhaust, clutch or transmission may also need to be checked or adjusted’. The wastegate must be adjusted during installation and calibration. No increase in power is automatic without the appropriate configuration.
Turbo part numbers
OEM part numbers
059145702L
059145702M
059145702R
059145702S
059145702F
059145715F
059145702LV
059145702FV
059145702MV
059145702RV
059145702SV
059145715FX
059145702FX
059145702MX
059145715FV
059145702RX
059145702LX
059145702SX
Manufacturer’s part numbers
53049700035
53049700043
53049700045
53049700050
53049700054
53049800035
53049800043
53049800045
53049800050
53049800054
53049880035
53049880043
53049880045
53049880050
53049880054
53049900035
53049900043
53049900045
53049900050
53049900054
Compatible vehicles and assignments
Audi
A4 B7 (8EC) — 204 hp
Diesel, November 2004 to June 2008
Engine code : BKN
A4 B7 (8EC) — 233 hp
Diesel, Jan 2006 to June 2008
Engine code : ASB
A4 B7 Front (8ED) — 204 hp
Diesel, November 2004 to June 2008
Engine code : BKN
A4 B7 Front (8ED) — 233 hp
Diesel, Jan 2006 to June 2008
Engine code : ASB
A4 B7 Convertible (8HE) — 204 hp
Diesel, Jan 2006 to Mar 2009
Engine code : BKN
A4 B7 Convertible (8HE) — 233 hp
Diesel, Jan 2006 to Mar 2009
Engine code : ASB
A6 Allroad C6 (4FH) — 211 hp
Diesel, May 2006 to August 2011
Engine codes: BNG, CDYB
A6 Allroad C6 (4FH) — 233 hp
Diesel, May 2006 to October 2008
Engine code : ASB
A6 C6 (4F2) — 211 hp
Diesel, May 2004 to March 2011
Engine codes: BNG, CDYB
A6 C6 (4F2) — 225 hp
Diesel, May 2004 to May 2006
Engine code : BMK, accuracy documented from May 2004
A6 C6 (4F2) — 233 hp
Diesel, June 2006 to October 2008
Engine code : ASB
A6 C6 Front (4F5) — 211 hp
Diesel, March 2005 to August 2011
Engine codes: BNG, CDYB
A6 C6 Front (4F5) — 225 hp
Diesel, March 2005 to May 2006
Engine code : BMK
A6 C6 Front (4F5) — 233 hp
Diesel, June 2006 to October 2008
Engine code : ASB
A8 D3 (4E2, 4E8) — 211 hp
Diesel, November 2003 to July 2010
Engine code : BNG
A8 D3 (4E2, 4E8) — 233 hp
Diesel, August 2003 to July 2010
Engine code : ASB
Q7 (4LB) — 211 hp
Diesel, March 2006 to May 2010
Engine codes: BUN, CASB
Q7 (4LB) — 233 hp
Diesel, March 2006 to May 2008
Engine code : BUG
Q7 Van (4LB) — 211 hp
Diesel, light commercial vehicle (LCV) type, March 2006 to May 2010
Engine codes: BUN, CASB
Q7 Van (4LB) — 232 hp
Diesel, light commercial vehicle (LCV) type, March 2006 to May 2008
Engine code : BUG
Volkswagen
Phaeton (3D1, 3D2, 3D3, 3D4, 3D6, 3D7, 3 — 224 hp
Diesel, September 2004 to May 2007
Engine code : BMK
Tuareg (7LA, 7L6, 7L7) — 211 hp
Diesel, April 2006 to May 2010
Engine codes: BUN, CASB
Tuareg (7LA, 7L6, 7L7) — 225 hp
Diesel, November 2004 to May 2010
Engine codes: BKS, CATA
Additional technical specifications
Product type: hybrid turbo
Documented engine specifications: 2.7 / 3.0 TDI
Fuel: diesel
Documented power ratings: 204, 211, 224, 225, 232 and 233 hp
Documented overall period: August 2003 to August 2011
Engine codes: ASB, BKN, BMK, BNG, CDYB, BUN, CASB, BUG, BKS, CATA
Installation: configuration plug & play documented
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the supply and the return d’the oil and the cleanliness of all the pipes’.
Check the intake and ensure there are no foreign objects. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions. The wastegate and engine management system must be adjusted in line with the chosen set-up.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger d…the original and compare it with the OEM and manufacturer’s specifications in this data sheet. Also check the make, model, generation, body style, engine type and power output in hp, the assembly period and the engine code. Having the same engine is not always enough to confirm compatibility.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact us with the full reference number of your turbocharger dVehicle origin and details.