This GT1749V hybrid turbocharger is designed for the 1.9 TDI AFN engine with 110 hp. Its tuning is based in particular on a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
Three tuning levels are documented. The choice of tuning package must take into account the engine configuration, the electronic control unit and the peripheral components.
Available tuning packages — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS high-flow
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This configuration is designed to adjust the compressor’s flow rate whilst maintaining documented performance Installation without modification. Its operation must be combined with appropriate engine settings.
Stage 2
Compressor impeller: MFS high-flow oversized
d intake housing: re-profiled for accommodate the new impeller oversized
Bearing stop: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
Reprofiling the housing allows d to adapt the impeller seat to the impeller oversized. This configuration may alter the flow capacity and behaviour of the turbocharger depending on the settings chosen.
Stage 2+
Compressor wheel: MFS high-flow oversized
d intake housing: re-profiled for accommodate the new impeller oversized
Bearing stop: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The documented specifications include an MFS oversized turbine and a d-intake housing adapted to. The final power output depends on the vehicle’s overall tuning and cannot be determined by the turbocharger alone.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate modified internal components. Depending on the stage, the modification may involve the compressor wheel, its geometry, its dimensions, the housings, the thrust bearing or the balancing.
The aim is d to adapt the compression capacity and air flow rate d. A hybrid turbo is not defined solely by the appearance of its impeller: consistency between the components and settings remains essential.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’: the impeller is machined from a solid block. The impeller shown here is made from forged aluminium and features a larger and taller geometry than the d'original.
A standard MFS impeller can be just as shiny as a ‘ Performance ’ MFS impeller. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. An increase in airflow can only be utilised properly with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement all influence its aerodynamic behaviour. The result also depends on the casings, the turbine wheel, the boost pressure and the mapping. A larger wheel therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces over a suitable surface. Balancing the rotor at 150,000 rpm on a Cimat VSR test bench helps to limit vibrations and mechanical stresses, though it does not compensate for poor installation or inadequate lubrication.
Engine remapping and preparation
d operation of a hybrid turbo may require adjustments to the mapping, boost pressure, fuel injection, exhaust system and cooling. The clutch, the transmission and other components must also be checked in accordance with the configuration. The wastegate must be adjusted when remapping the ECU.
Turbo part numbers
OEM part numbers
028 145 702E
028145702E
028145702EV
028145702EX
Manufacturer’s part numbers
454183-0001
454183-0002
454183-0003
454183-0004
454183-5001S
454183-5002S
454183-5003S
454183-5004S
Compatible vehicles and assignments
Assignments to be confirmed
No detailed list of vehicles is documented. Compatibility must be checked using the AFN engine code, the power output of 110 hp and the part numbers for the original turbo d.
Additional technical specifications
Product type: Hybrid Turbo
Turbo type: GT1749V
Engine: 1,.,9 TDI
Power: 110 hp
Engine code: AFN
Documented installation: no modifications
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the oil supply and return d. Check that the pipes are clean, the inlet and that there are no foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the turbo’s part number d, the original, OEM and manufacturer part numbers, as well as the vehicle, its generation, body style, engine type, power output,Year and engine code. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, contact ALFI TURBO with the full part number taken from your turbocharger.