This hybrid turbo for for the 1.7 CDTI engine (110 hp and 125 hp ) features d an internal modification designed to adapt the air flow d and the compression capacity. It is designed for for installation plug & play without any modifications to the mounting.
Depending on the package selected, the modification combines a high-flow MFS compressor impeller, a 360° thrust bearing, high-speed balancing and, on the most advanced configurations, recontouring of the casings or modification of the turbine section.
Available upgrades — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order d to adapt the air flow rate d whilst retaining the original mounting configuration without any external alterations.
Stage 2
Compressor impeller: MFS high-flow oversized
d ’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 2 combines a oversized compressor impeller with a reprofiled d intake casing. This modification is designed to utilise the new impeller geometry and may alter both the flow rate and the behaviour of the compressor.
Stage 3
Compressor impeller: MFS high-flow oversized
Casing d: Intake: Reprofiled for to accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration applies to both the compressor and turbine sides. The casings are re-profiled for to accommodate the oversized impellers, which may alter the air flow rate d, the gas flow rate and the response time depending on the associated engine tuning.
What is a hybrid turbo?
A hybrid turbo retains an architecture suited to the vehicle whilst incorporating internal modifications. Depending on the upgrade stage, these may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing or the balancing.
The aim is d'to adapt the compression capacity and the air flow rate d'. However, a hybrid turbo is not defined solely by the appearance of its impeller: the geometry of the components and their mechanical adaptation are crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. The wheel documented here is made from forged aluminium. This manufacturing process alone does not guarantee a higher air flow rate d.
A standard MFS impeller may retain a geometry close to the original. An MFS impeller intended for modification Performance may have a different geometry – for example, in terms of the profile, height, width or diameter of the blades – where such modifications are planned.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. The original specification d'indicates for that the MFS impeller used a design that is lighter, larger and taller than the original, with 15 per cent additional compression.
Why does the blade geometry affect the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour and the amount d of air displaced under certain conditions.
The result also depends on the casings, the turbine section, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee a better result and may alter the response time as well as the range d of optimal operation.
Reliability and balancing of the hybrid turbo
The 360° bearing stop present on all three stages helps to distribute axial forces. It does not eliminate the need d for proper lubrication or d for correct installation.
Each unit is balanced at high speed, up to 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor, without compensating for inadequate lubrication or incorrect installation.
Engine remapping and tuning
The engine ECU must be adapted for to make full use of the hybrid turbo’s characteristics. Depending on the level of tuning, the fuel injection, exhaust system, cooling, boost pressure and the transmission may also need to be checked or adjusted. The wastegate must be adjusted during reprogramming. The turbo alone does not guarantee a power gain.
Turbo specifications
OEM part numbers
860102
5860938
97376273
98102371
Manufacturer reference
VIFC
Compatible vehicles and assignments
Vehicle applications
No model, production period or engine code is documented in the available information. Compatibility must be confirmed using the original turbo part number d.
Additional technical specifications
Product type: Hybrid Turbo
Engine: 1.7 CDTI
Stated power outputs: 110 hp and 125 hp
Installation: Plug & play, no modifications required
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the oil supply and return lines d.
Check that the lines and the inlet are clean and free from foreign matter. Carry out the priming procedure in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further damage to the turbocharger.
How do you identify the correct turbo?
Check the turbo part number d the original, OEM and manufacturer part numbers, as well as the model, generation, body style, engine type, power output, mountingYear and the vehicle’s engine code. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this product description. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number from your original turbo d.