This GT1544 hybrid turbocharger is designed for the following engines 2.0 Di / DTi with 82 hp and 100 hp, compatible with the part numbers listed on this data sheet:.. Its modification combines a high-flow MFS compressor wheel, a 360° bearing retainer and high-speed balancing.
Three levels of preparation are documented at.. The modifications become more extensive depending on the package, particularly with regard to the impellers and the re-profiling of the casings.
Available set-ups — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration primarily modifies the compressor section to d adjust the compression capacity and air flow rate d whilst retaining a design geared towards direct integration.
Stage 2
Compressor impeller: MFS high-flow oversized
d' intake housing: re-profiled for accommodate the new impeller oversized
Thrust bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
The reprofiling of the intake housing d allows d to precisely adapt the housing to the compressor wheel oversized. This configuration can alter the air flow rate d and the compressor’s performance depending on the associated engine tuning.
Stage 3
Compressor wheel: MFS high-flow oversized
d'intake housing: re-profiled for to accommodate the new impeller oversized
Thrust bearing: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine casing: reprofiled for ly to accommodate the new impeller oversized
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification applies to both the compressor and turbine sides. The resulting performance depends on the overall engine configuration; a larger impeller alone does not guarantee better performance under all conditions.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for accommodate internal components that differ from the d original configuration. Depending on the upgrade stage, modifications may involve the compressor wheel, the turbine wheel, the housings, the thrust bearing system and the balancing.
The aim is d to adapt the compression capacity and the d air flow. However, a hybrid turbo is not defined solely by the appearance of its wheel: the geometry of the components and how they are combined are decisive.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process, but does not in itself guarantee an increase in air flow rate d.
A standard MFS impeller may retain a geometry equivalent to that of the original d. An MFS Performance impeller can be given a geometry tailored to the tuning objective. On this product, the impeller shown is made from forged aluminium, and is lighter, larger and taller than the original d.
A standard MFS impeller can be just as polished as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A higher airflow can help to generate more power when the engine is suitably tuned, though this alone does not guarantee a specific gain.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the intake air. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the volume d of air displaced within certain operating ranges.
The result also depends on the casings, the turbine wheel, the boost pressure and the engine management system. An increase in size can alter the response time as well as the optimal operating conditions d for the turbo.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces over a wide surface area. The rotor is balanced at high speeds, up to 150,000 rpm on a Cimat VSR test bench, to minimise vibrations and mechanical stresses.
These features do not compensate for inadequate lubrication, contamination of the system or incorrect installation.
Engine remapping and preparation
Operating d a hybrid turbo requires engine management tailored to its configuration. The mapping, boost pressure, fuel injection, exhaust and cooling must be monitored or adjusted according to the level of tuning.
The wastegate must be adjusted when remapping the ECU. The clutch, gearbox and other vehicle components may also require checking. A hybrid turbo does not automatically guarantee a power gain without appropriate tuning.
Turbo specifications
OEM part numbers
24442213
90531518
Manufacturer part numbers
454098-0001
454098-0002
454098-0003
454098-5003S
Turbo model: GT1544
Compatible vehicles and applications
No specific vehicle applications are documented. Compatibility must be confirmed based on the original turbo part number d, the engine type 2.0 Di / DTi and the power output of 82 hp or 100 hp.
Additional technical specifications
Product type: Hybrid Turbo
Engine type: 2.0 Di / DTi
Power: 82 hp, 100 hp
Part number: GT1544
Installation: plug & play configuration, with no documented modifications to the mounting
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d as well as the cleanliness of all pipes.
Check the inlet for any foreign objects. Prime the system in accordance with the applicable guidelines and follow the vehicle manufacturer’s instructions.
Failure to rectify a lubrication fault may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo d and compare it with the OEM and manufacturer part numbers in this data sheet. Also check the make, model, generation, body style, engine type, power output at hp, production period and engine code where available.
An identical engine specification is not always sufficient to confirm compatibility, as several different set-ups may co-exist.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number from your turbo.