This hybrid turbocharger, designed for the Opel 2.0 DTI engine producing 100 hp, is available in three documented performance levels.. Its design is adapted to each performance level by means of da high-flow MFS compressor wheel, da 360° bearing retainer and, for for the most advanced set-ups, d’a re-profiling of the casings and d’a modification to the turbine section.
The specifications listed apply in particular to the Opel Astra G, Signum, Vectra C and Zafira A. The tuning package must be selected according to the engine configuration and intended use.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrustbearing: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor wheel’s ability to move air. Its performance depends on the engine management system and the vehicle’s overall configuration.
Stage 2
Compressor wheel: MFS high-flow oversized
dintake housing: Reprofiled for to accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a reprofiled dintake housing. This modification is designed to alter the compression capacity and air flow rate d, though it does not, on its own, guarantee the final power output.
Stage 3
Compressor impeller: MFS high-flow oversized
Intake housing d: Reprofiled for to accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 3 modifies the compressor and turbine sides of the. The increased dimensions and reprofiling of both housings affect the flow rate and may also alter the response time as well as the turbo’s optimal operating range.
What is a hybrid turbocharger?
A hybrid turbo is based on a turbocharger architecture adapted for accommodate internal components that differ from the original configuration d. Depending on the stage, modifications may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing and the balancing.
The aim is dto adapt the compression capacity and air flow dto the requirements dof an engine tuning programme. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry, the adaptation of the housings and the balance of the assembly as a whole are crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow d. A standard MFS wheel can retain a geometry equivalent to that of the doriginal.
A standard MFS impeller can be just as glossy as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. In this modification, the wheels, documented as being oversized, are combined with a reprofiling of the corresponding housing. Increased airflow can contribute to a rise in power only when combined with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and arrangement of its blades all influence its aerodynamic behaviour. The result also depends on the housings, the turbine section, the boost pressure and the mapping. A larger impeller therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The 360° stop, documented at each stage, helps to distribute axial forces. The rotor is balanced at high speeds, up to 150,000 rpm, on a Cimat VSR test bench to minimise vibrations and mechanical stresses. However, this balancing does not compensate for either a lack of lubrication or incorrect installation.
Engine remapping and preparation
The engine management system must be adapted for to make full use of the hybrid turbo’s characteristics. The mapping, boost pressure and wastegate settings must be checked. Depending on the level of tuning, the fuel injection, exhaust, cooling, intake and transmission may also require checking or adjustment.
Turbo specifications
OEM part numbers
93184474
24461825
5860000
860058
Manufacturer part numbers
708867-0001
708867-0002
708867-1
708867-2
Compatible vehicles and applications
Opel
Astra G — 2.0 DTI — 100 hp
Period: from 2002, end date unspecified
Engine code : unspecified
Signum — 2.0 DTI — 100 hp
Period: from 2002, end unspecified
Engine code : unspecified
Vectra C — 2.0 DTI — 100 hp
Period: from 2002, end unspecified
Engine code : unspecified
Zafira A — 2.0 DTI — 100 hp
Period: from 2000, end unspecified
Engine code : unspecified
Zafira A Phase 2 — 2.0 DTI — 100 hp
Period: from 2000, end unspecified
Engine code : unspecified
Additional technical specifications
Product type: Hybrid Turbo
Internal reference: 708867
Motorisation: 2.0 DTI
Power: 100 hp
Installation: plug & play configuration, with no documented external modifications
Fitting instructions
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return lines d, the cleanliness of the pipes, and the intake, ensuring there are no foreign objects present.. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions.. A lubrication fault that is not rectified may result in further turbocharger failure.
How do you identify the correct turbo?
Check the part number of the original turbo dand compare it with the OEM and manufacturer part numbers listed. Also check the make, model, generation, engine type 2.0 DTI, power output (100 hp),Year and, where available, the engine code.. An identical engine specification does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your turbo’s identification plate d.