This hybrid turbo for engine options Chevrolet 1.7 VCDi and Opel 1.7 CDTI is available at three levels of difficulty. Depending on the course chosen, he receives an MFS compressor wheel Performance high flow rate, a 360° bearing stop and high-speed balancing.
The documented assignments relate in particular to Chevrolet Cruze and Trax, as well as the Opel Astra J, Corsa D, Meriva B and Mokka. Compatibility must always be confirmed using the turbo’s part number d’origin’.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS Performance high-throughput
Dimensions: 32.50 / 46.00 mm
Blade configuration: 6+6
Stop: 360° bearing
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This setup uses an MFS wheel Performance designed to regulate the flow rate d’air whilst retaining the documented dimensions for this work placement. The 360° stop helps to distribute axial forces.
Stage 2
Compressor wheel: MFS Performance high-capacity oversized
Dimensions: 36.40 / 49.00 mm
Blade configuration: 6+6
Carter d’Admission:’ re-profiled for to receive the new wheel
Stop: 360° bearing
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The larger diameter of the wheel requires the casing to be re-profiled d’admission’. This organisation aims to increase transport capacity d’air under suitable conditions, without this in itself constituting a guarantee of final power.
Stage 2+
Compressor wheel: MFS Performance high-capacity oversized
Dimensions: 38.40 / 52.00 mm
Blade configuration: 6+6
Carter d’Admission:’ re-profiled for to receive the new wheel
Stop: 360° bearing
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This workshop houses the largest wheel documented on this sheet, complete with a casing d’adapted admission’. Its behaviour depends on the overall engine set-up, and a larger wheel alone does not guarantee better performance in all conditions.
What is a hybrid turbo ?
A hybrid turbo is based on a turbocharger design that has been adapted to accommodate specific internal components. Depending on the design, modifications may relate to the compressor wheel, its dimensions, the geometry of the blades, the machining of the housings, the thrust bearing or the balancing.
The aim is d’adjust the compression capacity and flow rate’ dair. A hybrid turbocharger is therefore not defined solely by the appearance of its compressor wheel, but by the consistency of its mechanical characteristics.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in throughput dair. A standard MFS wheel can retain a geometry equivalent to that d’origin’.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. An MFS wheel Performance can be fitted with blades of a specific profile, dimensions or configuration suited to the preparation task. A higher flow rate can help to increase power output when the engine management system and components are correctly matched.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of the blades influence its aerodynamic behaviour and its ability to move air, depending on the operating conditions.
The result also depends on the compressor housing, the turbine section, the boost pressure and the engine tuning. An increase in diameter may affect the response time and the range doptimal use; it therefore does not automatically guarantee a better result.
Reliability and balancing of the hybrid turbocharger
The 360° bearing stop, as covered in the three training courses, distributes axial forces over a wide surface area. It helps to adapt the bearing system to operational stresses, without making the turbocharger immune to poor lubrication or incorrect installation.
Each batch is balanced at high speed, at 150,000 rpm, on a Cimat VSR test bench. Balancing is designed to minimise vibrations and mechanical stresses on the rotor.
Engine remapping and tuning
It may be necessary to adjust the engine mapping and boost pressure control for make the most of the hybrid turbo’s features. Depending on the level of preparation: fuel injection, exhaust, air cooling d’The intake, clutch or gearbox must also be checked’. The wastegate must be adjusted during the installation and remapping of the ECU. No increase in power is automatic without the right configuration.
Turbo part numbers
OEM part numbers
E55567731
55567731
E860198
860198
Manufacturer’s part numbers
789533-1
789533-2
789533-5001
789533-5002
789533-5001S
789533-5002S
Compatible vehicles and assignments
Chevrolet
Cruze (J300) — 110 hp
1.7 VCDi diesel — from November 2013 to an unspecified date
Engine code : LKR
Cruze (J300) — 131 hp
1.7 VCDi diesel vehicles — from January 2012 to an unspecified date
Engine code : LUD
Cruze Hatchback (J305) — 110 hp
1.7 VCDi diesel models — from August 2013 to December 2015
Engine code : LKR
Cruze Estate Car (J308) — 110 hp
1.7 VCDi diesel — from November 2013 to December 2015
Engine code : LKR
Cruze Estate Car (J308) — 131 hp
1.7 VCDi diesel — from August 2012, end date unspecified
Engine code : LUD
Trax — 131 hp
1.7 VCDi diesel engines — from December 2012, end date unspecified
Engine code : LUD
Opel
Astra J (P10) — 110 hp
1.7 CDTI diesel — from September 2009 to October 2015
Engine codes: A 17 DTC, A 17 DTE, A 17 DTJ
Astra J (P10) — 131 hp
1.7 CDTI diesel — from July 2011 to October 2015
Engine codes: A 17 DTF, A 17 DTS
Astra J Estate Van (P10) — 131 hp
1.7 CDTI diesel light commercial vehicles — from October 2012 to October 2015
Engine codes: A 17 DTF, A 17 DTS
Astra J GTC — 110 hp
1.7 CDTI diesel — from October 2011 to October 2020
Engine codes: A 17 DTC, A 17 DTE, A 17 DTJ
Astra J GTC — 131 hp
1.7 CDTI diesel — from October 2011 to October 2020
Engine codes: A 17 DTF, A 17 DTS
Astra J Hatchback Van (P10) — 110 hp
1.7 CDTI diesel light commercial vehicles — from May 2013 to October 2015
Engine codes: A 17 DTC, A 17 DTE
Astra J Saloon — 110 hp
1.7 CDTI diesel — from June 2012 to October 2015
Engine codes: A 17 DTC, A 17 DTE, A 17 DTJ
Astra J Saloon — 131 hp
1.7 CDTI diesel — from June 2012 to October 2015
Engine codes: A 17 DTF, A 17 DTS
Astra J Sports Tourer (P10) — 110 hp
1.7 CDTI diesel — from October 2010 to October 2015
Engine codes: A 17 DTC, A 17 DTE, A 17 DTJ
Astra J Sports Tourer (P10) — 131 hp
1.7 CDTI diesel — from October 2010 to October 2015
Engine codes: A 17 DTF, A 17 DTS
Corsa D (S07) — 130 hp
1.7 CDTI diesel — from December 2009 to August 2014
Engine code : At 17 DTS
Meriva B MPV (S10) — 110 hp
1.7 CDTI diesel — from June 2010 to June 2015
Engine codes: A 17 DTC, A 17 DTI
Meriva B MPV (S10) — 131 hp
1.7 CDTI diesel — from June 2010 to October 2013
Engine code : At 17 DTS
Meriva B Van (S10) — 110 hp
1.7 CDTI diesel light commercial vehicles — from January 2013 to October 2013
Engine code : At 17 DTC
Mokka / Mokka X (Day 13) — 131 hp
1.7 CDTI diesel — from June 2012, end date not specified
Engine code : At 17 DTS
Additional technical specifications
Product type: hybrid turbo
Editing: plug & play, without any modifications to the vehicle
Engine options: Chevrolet 1.7 VCDi and Opel 1.7 CDTI
Fuel: diesel
Powers dDocumented origins: 110, 130 and 131 hp
Engine codes: LKR, LUD, A 17 DTC, A 17 DTE, A 17 DTJ, A 17 DTF, A 17 DTS, A 17 DTI
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the supply and the return d’the oil and the cleanliness of all the pipes’.
Check the intake and ensure there are no foreign objects present. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions. The wastegate and engine management system must be set in line with the chosen tuning package.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger d…the original and compare it with the OEM and manufacturer’s specifications in this data sheet. Also check the make, model, generation, body style, engine type and power output in hp, the years of manufacture and the engine code. Having the same motor does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact us, quoting the reference number clearly visible on your turbocharger.