This hybrid turbocharger is designed for the following engines Toyota 1.4 D-4D 90 hp, as listed in this data sheet. Its specification includes, in particular, a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing on a Cimat VSR test bench.
Documented applications cover several generations of the Toyota, Auris, Corolla and Yaris. Compatibility must always be confirmed using the original turbo part number d.
Available tuning packages — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification is designed to adapt the compressor’s air flow rate dwhilst incorporating a thrust bearing designed for to distribute the axial forces more evenly. Its final performance depends on the engine’s configuration and settings.
Stage 2
Compressor impeller: MFS high-flow oversized
d’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The oversized impeller and the re-profiling of the dintake housing enabl dto adapt the airflow to this configuration. An increase in size may also alter the response time and the range d’ optimal use.
Stage 2+
Compressor impeller: MFS high-flow oversized
d’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This variant incorporates the mechanical modifications documented above. No power gain or additional dimensional differences are claimed without further technical data.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate internal modifications. Depending on the specification, these may relate to the compressor wheel, its dimensions or geometry, the housings, the turbine wheel, the thrust bearing system or the balancing.
The aim is dadapt the compression capacity and air flow rate d. A hybrid turbo is therefore not defined solely by the appearance of its compressor wheel, and its potential depends on the coherence of the entire mechanical assembly.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d. A standard MFS wheel may retain a geometry equivalent to that dof the original.
An MFS impeller Performance can be designed with a geometry tailored to the intended application: specific blade profile, dimensions or configuration, provided these elements are documented. A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air.
A higher d’air flow rate can contribute to the development d’of greater power with appropriate engine tuning, though it does not in itself guarantee results.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour. A suitable geometry can move more dair under certain operating conditions.
The result also depends on the housings, the turbine wheel, the boost pressure and the engine tuning. A larger turbine wheel does not automatically perform better in all conditions and may affect response time.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing featured on the three documented stages helps to distribute axial forces around the bearing system. However, it does not replace d’proper lubrication or d’correct installation.
The rotor is balanced at high speed, up to 150,000 rpm on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not protect the turbocharger against incorrect installation, contamination or a fault din the oil supply.
Engine remapping and preparation
Adjustments to the engine management system may be necessary for to make the most of the hybrid turbo’s characteristics. The mapping, boost pressure, injection, air cooling dthe intake, the exhaust and, depending on the vehicle, the transmission must be checked or adjusted. The wastegate must be adjusted during fitting and remapping. The hybrid turbo does not automatically guarantee a power gain without appropriate preparation.
Turbo part numbers
OEM part numbers — Toyota
17201-0N041
17201-0N042
Manufacturer’s part numbers
780708-0002
780708-0003
780708-0005
780708-5002S
780708-5003S
780708-5005S
GT1241VKZ
Compatible vehicles and configurations
Toyota
Auris 1.4 D-4D —90 hp
Engine variants 1.4 D-4D — from 2006, end dateunspecified
Engine code : unspecified
Auris Phase 2 1.4 D-4D — 90 hp
Engine 1.4 D-4D — from 2010, end date unspecified
Engine code : unspecified
Corolla 1.4 D-4D — 90 hp
Engine 1.4 D-4D — from 2005, end date unspecified
Engine code : unspecified
Yaris 3 1.4 D-4D — 90 hp
Engine 1.4 D-4D — from 2011, end date unspecified
Engine code : unspecified
Additional technical specifications
Product type: Hybrid Turbo
Engine: Toyota 1.4 D-4D
Power: 90 hp
Engine code: Not specified
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Carefully check the lubrication system, as well as the oil supply and return d. Check that the pipes and the inlet are clean and free from foreign objects.
Carry out the priming procedure in accordance with the applicable recommendations and follow the manufacturer’s instructions. The wastegate adjustment and engine management must be carried out by a qualified professional.
Unresolved lubrication issues may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the part number marked on the original turbo d, then compare the OEM and manufacturer part numbers.. Also check the make, model, generation and engine type 1.4 D-4D, power output from 90 hp, theYear and, where available, the engine code.. An identical engine specification does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If you are unsure about the identification or fitment, please contact us before ordering.