This hybrid turbo for, designed for the 2.0 D -4D 126 hp engine, is available in three tuning levels.. Its architecture plug & play is designed for for external Installation without modification, whilst its internal components are upgraded according to the selected stage.
The documented configurations combine a high-flow MFS compressor wheel, a 360° thrust bearing and high-speed balancing. The Stage 2 and Stage 3 feature additional mechanical modifications.
Available set-ups — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor wheel in order d to adjust the compression capacity and the d air flow. Its performance depends on the engine configuration and the turbocharging management system.
Stage 2
Compressor wheel: MFS high-flow oversized
d intake housing: Reprofiled for accommodate the new impeller oversized
Bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor wheel with a reprofiled d inlet housing. This modification is designed to correctly accommodate the new geometry and may alter the flow rate as well as the turbocharger’s response.
Stage 3
Compressor wheel: MFS high-flow oversized
d housing: Intake: Reprofiled for to accommodate the new wheel oversized
Thrust bearing system: 360° thrust bearing
Turbine wheel: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 3 includes modifications to both the compressor and turbine sides. This configuration may alter the turbo’s flow capacity and response characteristics; it must be combined with appropriate engine tuning.
What is a hybrid turbocharger?
A hybrid turbo utilises a turbocharger architecture adapted for accommodate internal components that differ from the original configuration d. Depending on the upgrade stage, modifications may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing system and the balancing.
The aim is d to adapt the compression capacity and d air flow. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: consistency between the wheels, housings and engine management remains crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d'air. A standard MFS wheel may retain a geometry equivalent to that d'of the original.
An MFS wheel Performance is characterised by a geometry tailored to the tuning objective. On this product, the wheel shown is made of forged aluminium, lighter, larger and taller than the d original; the technical data sheet indicates an additional compression capacity of 15 per cent.
A standard MFS impeller can be just as effective as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A higher airflow can only be utilised properly with a suitably tuned engine.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and its ability to move air.
. The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the turbo mapping. A larger impeller therefore does not automatically guarantee better performance and may alter the turbo’s response time.
Reliability and balancing of the hybrid turbo
The 360° bearing thrust ring, present on all three stages, helps to distribute the axial forces exerted on the rotating assembly. It does not, however, d'replace the need for proper lubrication or d'correct installation.
High-speed balancing at 150,000 rpm on a Cimat VSR test bench is designed to minimise vibrations and mechanical stresses on the rotor. It does not protect the turbocharger against incorrect installation, a fault d in the oil supply or the presence d of a foreign object.
Engine remapping and tuning
The engine ECU and boost pressure management must be adjusted for to make the most of the tuning’s characteristics. The wastegate must be adjusted during remapping. Depending on the configuration, the fuel injection, exhaust system, air d intake cooling, clutch or gearbox may also need to be checked or adjusted. Fitting d a hybrid turbo does not automatically guarantee a power gain.
Turbo specifications
OEM part numbers
17201-26051
17201-0R041
17201-0R040
1720126051
172010R041
172010R040
Manufacturer’s part numbers
VB21
VB19
Compatible vehicles and assignments
Confirmation of compatibility required
The 2.0 D -4D engine (126, hp ) is documented, but no make, model, production period or specific engine code is provided. Compatibility must be confirmed using the reference number of the original turbocharger d.
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.0 D -4D
Power: 126 hp
Installation: Plug & play, no external modifications required
Documented guides: Stage 1, Stage 2 and Stage 3
Installation tips
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbo.
Check the lubrication circuit, the oil supply and return lines d, and ensure all pipes are clean.
Check the intake for foreign objects and prime the system in accordance with the applicable recommendations. Follow the manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo d and compare it with the OEM and manufacturer part numbers in this sheet. Also check the make, model, generation, body style, engine type, power output ( hp), production period and engine code. An identical engine type is not always sufficient to confirm compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your original turbo d.