This hybrid turbo for, with the engine code Nissan 3.0 DCI and a power output of 115 hp, is available in three documented tuning stages.. Its design allows for Installation without modification, whilst the internal components vary depending on the selected stage.
The configurations utilise a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing. The Stage 2 and Stage 3 feature additional mechanical modifications to the wheels and casings.
Available configurations — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: high-flow MFS
Bearing: 360° thrust
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order d to adapt the flow rate d to the air, whilst retaining a configuration designed for installation without modification.
Stage 2
Compressor impeller: high-flow MFS oversized
d' intake housing: re-profiled for accommodate the new impeller oversized
Bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a reprofiled d intake casing. This modification is designed to increase air displacement capacity d, subject to d suitable engine and peripheral management.
Stage 3
Compressor impeller: high-flow MFS oversized
d intake housing: re-profiled for to accommodate the new impeller oversized
Bearing: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration alters the compressor and turbine sides. Oversizing may improve flow rate, but it can also affect response time and the conditions d for optimal use of the turbocharger.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for accommodate modified internal components. Depending on the stage, the modification may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing and the balancing of the rotor.
The aim is d to adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometries, machining and overall consistency of the unit are crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process and does not, on its own, guarantee an increase in flow rate. A standard MFS wheel can retain a geometry equivalent to that of the d original.
An MFS impeller Performance can be designed with a geometry suited to the engine set-up. In this product, the impeller shown is made of forged aluminium; it is lighter, larger and taller than the original d; the documentation indicates an additional compression capacity of 15 per cent.
A standard MFS impeller can be just as polished as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher airflow can contribute to power output only when combined with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air admitted by the engine. Its diameter, profile, height, width and arrangement of its blades all influence its aerodynamic behaviour. The result also depends on the housings, the turbine, the boost pressure and the mapping. A larger impeller therefore does not automatically guarantee better performance in all conditions.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces over a wide surface area. The rotor is balanced at high speed, up to 150,000 rpm on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. However, this balancing does not compensate for incorrect installation or inadequate lubrication.
Engine remapping and preparation
Appropriate engine management is required for to make the most of the hybrid turbo’s characteristics. The mapping, boost pressure, fuel injection, exhaust and cooling must be checked or adjusted depending on the modification. The wastegate must be adjusted when the ECU is remapped. The transmission and other components must also be checked depending on the vehicle.
Turbo part numbers
OEM part numbers
1441169T60
14411-69T60
14411 69T60
Manufacturer part numbers
709693-0001
709693-5001S
GT2252S
Compatible vehicles and applications
Nissan
Model not specified — 115 hp
Engine 3.0 DCI — period unspecified
Engine code: not specified
As the specific model is not documented, compatibility must be confirmed using the reference number of the original d turbocharger.
Additional technical specifications
Product type: hybrid turbo
Engine: 3.0 DCI
Power: 115 hp
Main part number: 709693
Turbo model: GT2252S
Installation: no modifications required
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d as well as the cleanliness of all pipes.
Check the inlet and ensure that no foreign objects can reach the compressor. Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number engraved or marked on the original turbo d, then compare the OEM and manufacturer part numbers. The make, model, generation, body style, engine type, power output, production period and engine code must also be checked. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this product sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number and a clear photo of the turbo’s identification plate d.