This hybrid turbo is designed for engine options Kia 2.5 TCI and 2.7 TD compatible. Depending on the model chosen, its design incorporates a high-flow MFS compressor wheel, a 360° bearing stop and internal modifications designed to adjust the compression capacity and flow rate dair.
The documented assignments relate in particular to Kia Frontier, H100, Light Truck, Porter, Pregio and Sportage. The assembly is designed in accordance with a specific design plug & play, without any modifications to the vehicle, subject to a thorough check of the part numbers d’origin’.
Available products — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: High-capacity MFS
Level: 360° stop
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This product acts primarily on the compressor section in order to d’adjust the flow rate’ dair. The 360° stop helps to distribute the axial forces acting on the rotating assembly.
Stage 2
Compressor wheel: High-capacity MFS oversized
Carter d’Admission:’ reprofiled for to accommodate the new wheel oversized
Level: 360° stop
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 is fitted with a compressor wheel oversized as well as a casing d’re-profiled intake’. This combination aims to adapt the airflow to the new geometry, with behaviour that also depends on the engine settings and conditions dUse.
Stage 3
Compressor wheel: High-capacity MFS oversized
Carter d’Admission:’ reprofiled for to accommodate the new wheel oversized
Level: 360° stop
Turbine wheel: high-speed oversized
Turbine casing: reprofiled for to accommodate the new wheel oversized
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The Stage 3 modifies the compressor and turbine sides. Both casings have been reshaped for to accommodate the oversized wheels, which allows dto adjust the flow rate jointly d’compressed air and gas flow’ dexhaust. This configuration may affect the engine’s response characteristics and must be incorporated into a coherent engine tuning programme.
What is a hybrid turbo ?
A hybrid turbo is based on a specially adapted turbocharger design for to receive internal components that differ from the configuration d’origin’. Depending on the service, modifications may involve the compressor wheel, the turbine wheel, the casings, the thrust bearing system and balancing.
The aim is d’adjust the compression capacity and flow rate’ dair to meet the requirements of the preparation. However, a hybrid turbocharger is not defined solely by the appearance of its compressor wheel: the geometry of the wheels, the machining of the housings and the overall coherence of the assembly are all crucial factors.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This term describes a manufacturing process and does not, in itself, guarantee an increase in flow rate dair.
A standard MFS wheel can retain a geometry equivalent to that d’origin’. An MFS wheel Performance may, depending on the design specifications, have a blade profile, diameter or configuration suited to a specific flow rate objective.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. A higher flow rate can enable the engine to produce more power when combined with appropriate engine tuning, although this does not in itself guarantee a performance gain.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air, which is then sent to the engine. Its diameter, profile, height, width and the arrangement of its blades all influence its aerodynamic behaviour. The right geometry can move more dair within certain operating ranges.
The result also depends on the casings, the turbine wheel, the boost pressure and the engine tuning. A larger wheel therefore does not automatically guarantee a better result and may affect the response time as well as the range doptimal use.
Reliability and balancing of the hybrid turbocharger
The 360° stop, which is featured in each documented stage, distributes the axial forces around the axis. It helps to ensure the mechanical integrity of the assembly, without eliminating the constraints associated with lubrication, assembly or operating conditions dUse.
The rotor is balanced at high speed – 150,000 rpm – on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not compensate for a lack of lubrication, contamination of the system or incorrect installation.
Engine remapping and tuning
It may be necessary to adjust the engine management system for make the most of the features da hybrid turbo. Depending on the course and the vehicle, it is advisable to check the engine mapping, boost pressure control, fuel supply and air cooling d’intake, exhaust and transmission capacity’.
Replacing the turbocharger does not automatically guarantee a gain in power. The modifications must be consistent with the engine, its components and the vehicle’s intended use.
Turbo part numbers
OEM part numbers
2820042610
28200-42610
28,200–42,700
28200-43160
Manufacturer’s part numbers
715924-0001
715924-1
715924-5001S
715924-3
715924-0003
715924-5003S
Compatible vehicles and assignments
Kia
Frontier 2.5 D — 100 hp
Engine 2.5 D — from 2002, end date unspecified
Engine code : not specified
H100 2.5 D — 100 hp
Engine 2.5 D — from 2002, end date unspecified
Engine code : not specified
Light Truck 2.5 D — 100 hp
Engine 2.5 D — from 2002, end date unspecified
Engine code : not specified
Porter 2.5 D — 100 hp
Engine 2.5 D — from 2002, end date unspecified
Engine code : not specified
Pregio 2.5 TCI — 94 hp
Engine 2.5 TCI — from 1999, end date unspecified
Engine code : not specified
Sportage 2.5 TD — 83 hp
Engine 2.5 TD — from 2002, end date unspecified
Engine code : not specified
Additional technical specifications
Product type: hybrid turbo
Engine specifications: 2.5 TCI and 2.7 TD
Allocation powers: 83, 94 and 100 hp
Assembly design: plug & play, without any modifications to the vehicle
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Search for and correct the cause of the previous failure before d’fit the turbocharger’.
Check the lubrication circuit, the supply and the return doil. Check that the ducts and the intake are clean and free from foreign objects.
Carry out priming in accordance with the relevant guidelines and follow the vehicle manufacturer’s instructions.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger d…the original and compare it with the OEM and manufacturer’s specifications in this data sheet. Also check the make, model, version, engine type and power output in hp, theYear installation details and, where available, the engine code.
The same engine can be fitted with several different turbocharger set-ups. Checking that the reference numbers match therefore remains the most reliable method of verification.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact us, quoting the reference number clearly visible on your turbocharger d’origin’.