This hybrid turbocharger, designed for the following engines: 1.4 HDi, 1.4 TDCi and 1.4 D, features internal modifications tailored to the selected package.. The documented configurations combine a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
Applications include, in particular, the Citroën, Ford, Peugeot and Toyota models producing 54 or 68 hp. Compatibility must always be confirmed using the original turbo part number d.
Available tuning options — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration focuses on adapting the compressor impeller to alter the compression capacity and air flow rate d, whilst retaining the other documented characteristics of the Stage 1.
Stage 2
Compressor impeller: MFS high-flow oversized
d ’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor wheel with a reprofiled d intake housing. This modification is designed to ensure the correct fit and operation of the new wheel, with performance depending on the engine preparation and operating conditions d.
Stage 3
Compressor impeller: MFS high-flow oversized
Intake casing d: Reprofiled for to accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine housing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration includes modifications to both the compressor and turbine sides. The sizing of the impellers and the re-profiling of the housings influence both the flow rate and the response of the turbocharger; the result depends on the overall engine configuration.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for accommodate modified internal components. Depending on the stage, the modification may involve the compressor wheel, the turbine wheel, the housings, the thrust bearing system and balancing.
The aim is d to adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its impeller: its geometry, the adaptation of the housings and the overall coherence of the assembly are crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’: the impeller is machined from a solid block. For this product, the compressor impeller is specified as forged aluminium and its configuration Performance is lighter, larger and taller than the original d.
A standard MFS impeller can retain a geometry equivalent to the original. An MFS impeller Performance features a geometry tailored to the tuning objective and can therefore alter the volume d of air displaced.
A standard MFS impeller can be just as efficient as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A higher airflow rate can contribute to power output with a suitably tuned engine, though this alone does not guarantee a specific result.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the amount d of air it can move under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee a better result and may alter the response time as well as the range d of optimal operation.
Reliability and balancing of the hybrid turbo
The 360° bearing thrust ring helps to distribute axial forces around the shaft. Here, it complements the documented internal modifications, without making the turbocharger immune to a lack of lubrication or incorrect installation.
The rotor is balanced at high speed, at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses during operation.
Engine remapping and preparation
The engine management system must be adapted for to make full use of the hybrid turbo’s characteristics. The wastegate must be adjusted during the ECU reprogramming.
Depending on the level of tuning, the fuel injection, boost pressure, exhaust system, cooling, intake and transmission must be checked or adjusted. Fitting d a hybrid turbo does not automatically guarantee a performance gain without a coherent set-up.
Turbo specifications
OEM part numbers
96 615 574 80
9661557480
Manufacturer part numbers
54359700021
54359800021
54359880021
54359900021
Compatible vehicles and applications
Citroën
C1 — 1.4 HDi —54 hp
From 2005, end date unspecified
Engine code : unspecified
C2 — 1.4 HDi — 68 hp
From 2003, end date unspecified
Engine code : unspecified
Nemo — 1.4 HDi — 54 hp
From 2007, end date unspecified
Engine code : unspecified
Ford
Fiesta 5 — 1.4 TDCi — 68 hp
From 2001, end date unspecified
Engine code : unspecified
Peugeot
107 — 1.4 HDi — 54 hp
From 2005, end date unspecified
Engine code : unspecified
Bipper — 1.4 HDi — 54 hp
From 2008, end date unspecified
Engine code : unspecified
Toyota
Aygo — 1.4 D — 54 hp
From 2005, end date unspecified
Engine code : unspecified
Additional technical specifications
Product type: Hybrid Turbo
Engine variants: 1.4 HDi, 1.4 TDCi and 1.4 D
Documented power outputs: 54 and 68 hp depending on the vehicle
Fitting: Installation with no documented external modifications
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbocharger.
dCheck the lubrication system, the oil supply and return lines, and ensure the pipes are clean. Also check the intake for any foreign objects.
Carry out the priming procedure in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may lead to the turbocharger failing again.
How do you identify the correct turbo?
Check the part number engraved or marked on the original turbo d, then compare the OEM and manufacturer part numbers.. Also check the make, model, generation, engine type, power output at hp, theYear and, where available, the engine code.
The same engine type may be fitted with several different turbochargers depending on the vehicle version.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your original turbocharger d.