This hybrid turbocharger is designed for for direct fitment on the applications documented at Volvo. Its specification combines a high-flow MFS compressor wheel, a 360° bearing retainer and high-speed balancing, with additional modifications depending on the chosen performance stage.
Applications include, amongst others, the Volvo 850 T5, C70, S70 T5 and V70 T5. The part number of the original turbo d must be checked before placing an order.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order d to adapt the flow rate d to the air. The 360° thrust bearing helps to distribute axial forces more evenly during operation.
Stage 2
Compressor impeller: MFS high-flow oversized
d' intake housing: re-profiled for accommodate the new impeller oversized
Thrust bearing: 360° bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 2 is fitted with a oversized compressor impeller and a d intake housing adapted to. This combination is designed to alter the compression capacity and air flow rate d, with performance depending on the engine configuration.
Stage 3
Compressor impeller: MFS high-flow oversized
Intake housing d: reprofiled for to accommodate the new impeller oversized
Thrust bearing: 360° bearing
Turbine impeller: high flow rate oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This version modifies the compressor and turbine sides. The sizing of the impellers and the re-profiling of the housings influence the flow rate, load ramp-up and d the optimal operating conditions of the turbocharger.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for accommodate internal components that differ from the original configuration d. Depending on the stage, modifications may involve the compressor wheel, the turbine wheel, the housings, the thrust bearing and the balancing.
The aim is d to adapt the compression capacity and the d air flow. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry of the wheels, the machining of the housings and the overall balance are crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This is d a manufacturing process which, on its own, does not guarantee an increase in air flow d.
A standard MFS impeller may retain a geometry equivalent to the original. An MFS impeller Performance may adopt a geometry adapted to the modification, particularly through its profile, dimensions or the configuration of its blades, where such modifications are intended.
A standard MFS impeller can be just as glossy as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A higher airflow can contribute to power output with appropriate engine tuning, though it does not, on its own, guarantee a specific result.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour. A suitable geometry can move more d air within certain operating ranges.
The result also depends on the housings, the turbine wheel, the boost pressure and the engine tuning. A larger turbine wheel therefore does not automatically guarantee better performance and may alter the turbo’s response time.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing fitted to each documented stage distributes axial forces over a wide surface area. However, it does not protect the turbocharger against a lack of lubrication, contamination or incorrect installation.
The assembly is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor.
Engine remapping and preparation
The engine management system must be adapted for to make full use of the hybrid turbo’s characteristics. The wastegate must be adjusted during the ECU reprogramming.
Depending on the level of tuning, the fuel injection, exhaust system, cooling, boost pressure and transmission must be checked or adjusted. Fitting the turbo does not automatically guarantee a power gain without appropriate engine configuration.
Turbo part numbers
OEM part numbers
1270536
1275663
8601238
Manufacturer part numbers
49189-01330
49189-01335
49189-01350
49189-01355
Compatible vehicles and applications
Volvo
850 T5 — 240 hp
2.3 T — from 1991, end date unspecified
Engine code : unspecified
C70 — 240 hp
2.3 i — from 1997, end unspecified
Engine code : unspecified
S70 T5 — 225 hp
2.0 i — from 1996, end date unspecified
Engine code : unspecified
V70 T5 — 240 hp
2.3 i — from 1996, end date unspecified
Engine code : unspecified
V70 T5 — 250 hp
2.3 i — from 1996, end date unspecified
Engine code : unspecified
Additional technical specifications
Product type: hybrid turbo
Installation: direct fit without vehicle modifications, subject to compatibility
Documented engine variants: 2.0 i, 2.3 i and 2.3 T
Documented power outputs: 225, 240 and 250 hp
Engine codes: not specified
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d, and ensure all pipes are clean.
Check the inlet for any foreign objects. Prime the system in accordance with the applicable guidelines and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further failure of the turbocharger.
How do you identify the correct turbo?
Check the part number marked on the original turbo d and compare it with the OEM and manufacturer part numbers in this data sheet. Also check the make, model, version, engine type, power output, mountingYear and engine code where available.
A similar engine may be fitted with several different turbo set-ups depending on the version or production period.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine does not always guarantee compatibility.
If in doubt, please contact us with the full part number from your turbo.