This for hybrid turbo, with a 2.8 CRD engine, features dan internal modification designed to adjust the air flow daccording to the selected stage. The documented configurations combine a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
The available fitments cover several versions of the Jeep Cherokee, Cherokee KJ and Liberty models with power outputs of 150, 160 or 163 hp. Installation is designed to require no modification d’to the turbocharger, subject to precise verification of the original part number d.
Available kits — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing: 360° thrust
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification affects the compressor section in order d’ adapt its displacement capacity d’ air, whilst retaining a configuration d’Installation without modification d ’ documented adaptation.
Stage 2
Compressor wheel: MFS high-flow oversized
d’inlet housing: re-profiled for to accommodate the new impeller oversized
Bearing: 360° thrust
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor wheel with a reprofiled dintake housing. This modification is designed to ensure the wheel and its housing operate together under the conditions specified by the preparation.
Stage 3
Compressor impeller: MFS high-flow oversized
d’ intake housing: re-profiled for to accommodate the new impeller oversized
Bearing: 360° thrust
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This configuration includes documented modifications on both the compressor and turbine sides. Oversizing may alter the flow rate as well as the behaviour of the turbocharger; its operation must be adapted to the complete engine configuration.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for accommodate modified internal components. Depending on the stage of the project, the modifications may involve the compressor wheel, the casings, the turbine wheel, the thrust bearing and balancing.
The aim is dto adapt the compression capacity and air flow rate d. A hybrid turbo is not defined solely by the appearance of its impeller: consistency between the geometry of the impellers, the housings and the operating conditions is essential.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in airflow d. A standard MFS wheel can retain a geometry equivalent to that dof the original.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. Depending on its design, a Performance impeller may utilise a blade profile, dimensions or configuration tailored to the intended application. A higher airflow rate can help generate more power with the appropriate engine tuning, though it does not, on its own, guarantee a performance gain.
Why does blade geometry influence air flow d?
The compressor impeller draws in and then compresses the air. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour. A suitable geometry can move more dair under certain conditions, but the result also depends on the casings, the turbine, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° stop helps to distribute the axial forces exerted on the rotating assembly. The rotor is balanced at high speed, at 150,000 rpm on a Cimat VSR test bench, to minimise vibrations and mechanical stresses. However, this balancing does not compensate for incorrect installation or inadequate lubrication.
Engine remapping and preparation
Adjustments to the engine management system may be necessary for to make the most of the hybrid turbo’s characteristics. Depending on the level of tuning, it is advisable to check the mapping, boost pressure, fuel supply, intake air cooling d, the exhaust system, and the capacity of the clutch or gearbox.. Fitting da hybrid turbo does not automatically guarantee a power gain.
Turbo specifications
OEM part numbers
35242112G
35242115F
Manufacturer part numbers
757246-0001
757246-1
763360-0001
763360-1
763360-5001S
Compatible vehicles and roles
Jeep
Cherokee KJ 2.8 CRD –150 hp
Engine variants: 2-., 8- CRD — from 2001, end date unspecified
Engine code: not specified
Cherokee 2.8 CRD — 163 hp
Engine variants: 2-., 8- CRD — from 2004, end date unspecified
Engine code: not specified
Liberty 2.8 CRD — 160 hp
Engine variants: 2-., 8- CRD — from 2004, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: turbo hybrid
Engine: 2.8 CRD
Documented power outputs: 150, 160 and 163 hp
Installation: no modifications requ ddocumented adaptation
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d, as well as the cleanliness of the pipes. Check the inlet and ensure there are no foreign objects. Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions. An uncorrected lubrication fault may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the part number marked on the turbo dthe original part number, the OEM and manufacturer part numbers, as well as the make, model, generation, engine type, power output,Year and engine code. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this product sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your turbocharger.