This hybrid turbo is designed for a 2.0 CDI engine with 140 hp. Its specification is based on a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing, with additional modifications depending on the selected upgrade package.
Designed for a Installation without modification, it must be identified using the original turbo part numbers d. To make the most of its performance characteristics, a suitable engine configuration is required.
Available tuning options — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust system: 360° bearing thrust
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification is carried out on the compressor impeller in order d to adjust the compression capacity and the air flow rate d. The 360° thrust bearing helps to distribute the axial forces borne by the rotating assembly.
Stage 2
Compressor wheel: MFS high-flow oversized
d'intake housing: re-profiled for accommodate the new impeller oversized
Bearing system: 360° bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a d intake housing, re-profiled. This modification is designed to correctly accommodate the new geometry and adjust the available air flow d, without assuming d a final engine power output.
Stage 3
Compressor impeller: MFS high-flow oversized
d intake housing: re-profiled for to accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine housing: reprofiled for ly to accommodate the new impeller oversized
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This version includes modifications to both the compressor and turbine sides. The final performance depends on the overall configuration, in particular the housings, boost pressure and engine tuning.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate internal components that differ from the d original configuration. Depending on the stage, the modification may involve the compressor wheel, the turbine wheel, the casings, the thrust bearing system and balancing.
The aim is d to adapt the compression capacity and the air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its impeller: the geometry of the components and how they are combined determine its behaviour.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes its manufacturing process, but does not in itself guarantee an increase in air flow rate d. A standard MFS wheel may retain a geometry equivalent to that d of the original.
An MFS wheel Performance can be given a geometry tailored to the tuning objective. For this product, the wheel is described as lighter, larger and taller than the d original, with an advertised 15 per cent increase in compression capacity.
A standard MFS impeller can be just as efficient as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher airflow can contribute to power output with appropriate engine tuning, though it does not in itself guarantee results.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the volume d of air displaced under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee better performance and may alter the response time as well as the range d of optimal operation.
Reliability and balancing of the hybrid turbo
The 360° bearing stop, documented at each stage, distributes the axial forces around the shaft. It helps the turbo adapt to operating stresses, without protecting it d from a lubrication fault or d from incorrect installation.
The rotating assembly is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor.
Engine remapping and preparation
The engine mapping and boost pressure management must be adjusted for to make full use of the hybrid turbo’s characteristics. The wastegate must be adjusted whilst remapping the ECU.
Depending on the level of tuning, the fuel injection, exhaust, cooling, intake, clutch or transmission may also require checking or adjustment. Fitting the turbo alone does not guarantee any increase in power.
Turbo part numbers
OEM part numbers
6400900980
6400901480
6400901580
6400901680
6 400 900 980
6,400,901,580
6,400,901,680
Manufacturer’s part numbers
53039707000
53039707001
53039807000
53039807001
53039887000
53039887001
53039907000
53039907001
Compatible vehicles and assignments
No specific vehicle compatibility is documented. Compatibility must be confirmed based on the original turbo d part numbers and the vehicle’s specifications.
Additional technical specifications
Product type: hybrid turbo
Engine: 2.0 CDI
displacement: 2.0 l
Power: 140 hp
Installation: no modifications required
Engine code: not specified
Fitting period: not specified
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d as well as the cleanliness of all pipes.
Check the inlet for any foreign objects. Prime the system in accordance with the applicable guidelines and follow the vehicle manufacturer’s instructions.
Failure to rectify a lubrication fault may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo d and compare it with the OEM and manufacturer part numbers in this data sheet. Also check the make, model, generation, body style, engine type, power output ( hp), production period and engine code where available. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number of the original turbo d and the vehicle details.