This hybrid turbo for engine Mercedes 2.7 CDI combines a plug & play -type setup with internal modifications tailored to the chosen tuning level. The three stages documented utilise a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
The specifications listed apply in particular to the C270 ‘ Mercedes ’ in W203 and T203 body styles, as well as the CLK 270 Coupé (type 209), with a documented power output of 170 hp.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification is carried out on the compressor impeller in order d to adjust the compression capacity and the air flow rate d, whilst retaining the mechanical configuration documented for in this stage.
Stage 2
Compressor impeller: MFS high-flow oversized
Intake casing d: re-profiled for accommodate the new impeller oversized
Bearing thrust ring: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a d intake housing, re-profiled. This modification is designed to correctly accommodate the new geometry and to promote a higher air flow rate d under appropriate operating conditions.
Stage 3
Compressor impeller: MFS high-flow oversized
Intake housing d: re-profiled for to accommodate the new impeller oversized
Bearing thrust ring: 360°
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification alters the compressor and turbine sides. The housings are re-profiled for accommodate the oversized impellers, which may alter the available flow rate, response time and range d'optimal use of the turbocharger.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for to accommodate internal components that differ from the d original configuration. Depending on the stage, modifications may involve the compressor wheel, its dimensions, the housings, the turbine wheel, the thrust bearing or the balancing.
The aim is d to adapt the compression capacity and the d air flow. However, a hybrid turbo is not defined solely by the appearance of its impeller: the consistency between the impellers, the housings, the balancing and the engine management remains crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in flow rate. A standard MFS wheel can retain a geometry equivalent to the original.
An MFS impeller Performance can be given a geometry tailored to the application: the profile, height, width or diameter of the blades may be adjusted where such modifications are required. The data provided for this product describes a forged aluminium wheel that is lighter, larger and taller than the original, with a claimed compression capacity up to 15 per cent higher.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher flow rate can only be fully utilised with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air admitted by the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour. A suitable geometry can move more d air within certain operating ranges.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine calibration. A larger impeller therefore does not automatically guarantee a better result and may alter the response time.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing, documented across the three stages, helps to distribute the axial forces exerted on the rotating assembly. However, it does not protect the turbocharger against lubrication failure, contamination or incorrect fitting.
Each engine preparation undergoes d ‘high-speed balancing at 150,000 rpm on a Cimat VSR test bench’. This process aims to minimise vibrations and mechanical stresses on the rotor during operation.
Engine remapping and tuning
Appropriate engine management is required for to make full use of the hybrid turbo’s characteristics. The mapping, boost pressure and wastegate settings must be checked during remapping. Depending on the level of tuning, the fuel injection, exhaust system, cooling system, induction and the transmission may also require checking or adjustment. Fitting d a hybrid turbo alone does not guarantee a power gain.
Turbo part numbers
OEM part numbers
A6110960999
6120960999
A6120960499
6120960499
612096049980
Manufacturer’s part numbers
711009-0001
711009-0002
711009-1
711009-2
711009-5002s
Compatible vehicles and assignments
Mercedes
C270 W203 — 170 hp
2.7 CDI — from 2000, end date unspecified
Engine code: not specified
C270 T203 — 170 hp
2.7 CDI — from 2001, end date unspecified
Engine code: not specified
C270 W203 Phase 2 — 170 hp
2.7 CDI — from 2004, end date unspecified
Engine code: not specified
C270 T203 Phase 2 — 170 hp
2,.,7, CDI — from 2004, end date unspecified
Engine code: not specified
CLK 270 type 209 Coupé — 170 hp
2,.,7, CDI — from 2002, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.7 CDI
Fuel: Diesel
Power Documented: 170 hp
Fitting: plug & play, no modifications required d' installation documented
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbocharger.
Check the lubrication circuit, the oil supply and return d. Ensure the pipes and inlet are clean and free from foreign objects.
Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions. The wastegate must be adjusted as part of d ‘a suitable engine calibration’.
Unresolved lubrication issues may lead to further turbocharger failure.
How do you identify the correct turbocharger?
Check the part number marked on the original turbo d as well as the OEM and manufacturer part numbers.. Also check the make, model, generation, body style, engine type 2.7 CDI, power output 170 hp, installation period and, where available, the engine code.
An identical engine may be fitted with several different turbo set-ups. Comparing part numbers therefore remains the most reliable way to confirm compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine does not always guarantee compatibility.
If in doubt, contact our team with the part number clearly visible on your original turbo d.