This GT1852V hybrid turbocharger is designed for the following engines CDI, and features dan internal configuration tailored to the selected performance level. The documented configurations combine a high-flow MFS compressor wheel, a 360° bearing thrust ring and high-speed balancing.
The specifications listed apply in particular to several Mercedes Class C and Class E models. Installation is designed to require no modification d’adaptation on compatible applications, but the engine configuration must be adjusted to the selected tuning level.
Available tuning levels — Stage 1, Stage 2 and Stage 3
Stage 1
MFS high-flow compressor wheel
360° thrust bearing
Balanced at 150,000 rpm on a Cimat VSR test bench
This configuration enhances compression capacity and air flow dthanks to the MFS impeller, whilst retaining the documented casing configuration.
Stage 2
High-flow MFS compressor impeller oversized
d’ intake housing reprofiled to for commodate the new impeller
360° thrust bearing
Balancing at 150,000 rpm on a Cimat VSR test bench
The reprofiling of the casing enabl dto integrate the compressor impeller oversized. This design aims to achieve an air flow rate dsuited to a coherent engine tuning programme.
Stage 3
High-flow MFS compressor wheel oversized
d’s reprofiled intake housing
360° thrust bearing
High-flow turbine impeller oversized
for ’s re-profiled turbine housing to accommodate the new impeller
Balancing at 150,000 rpm on a Cimat VSR test bench
This version combines modifications to both the compressor and turbine sides of the. The larger dimensions may affect flow rate and response time; its performance depends on the overall engine set-up.
What is a hybrid turbo?
A hybrid turbo retains an architecture suited to the application’s original mounting points d, whilst incorporating modified internal components.. Depending on the stage, the modification may involve the compressor wheel, the housings, the thrust bearing or even the turbine wheel.
The aim is dto adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its impeller: its geometry, the machining of the housings, the balancing and the consistency between the components are all crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in flow rate. A standard MFS wheel may retain a geometry equivalent to the original.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. On this product, the tuning packages use a high-flow MFS impeller, oversized for Stages 2 and 3.
Why does the geometry of the blades influence the air flow rate d?
The diameter, profile, height, width and arrangement of the blades all influence air intake and compression. The result also depends on the casings, the turbine, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee better performance in all conditions and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces over a wide surface area. The rotor is balanced at high speeds, up to 150,000 rpm, on a Cimat VSR test bench to minimise vibrations and mechanical stresses. This balancing does not compensate for faults in assembly or lubrication.
Engine remapping and preparation
Adjustments to the mapping and boost pressure control are necessary for to make full use of the turbo’s characteristics. The wastegate must be adjusted during remapping. Depending on the modification, the fuel injection, exhaust system, cooling system, the intake and the transmission may also need to be checked or adjusted.
Turbo part numbers
OEM part numbers
6110960999
A611 096 0999
A6110960999
Manufacturer part numbers
711006-0001
711006-0003
711006-5001S
711006-5003S
GT1852V
Compatible vehicles and applications
Mercedes
C200 (W203) — 116 hp
2.1 CDI — from 2000, end date unspecified
Engine code : unspecified
C200 (T203) — 116 hp
2.1 CDI — from 2001, end date unspecified
Engine code : unspecified
C220 (W203) — 136 and 143 hp
2.1 CDI — from 2000, end date unspecified
Engine code : unspecified
C220 (C203) — 143 hp
2.1 CDI — from 2000, end date unspecified
Engine code : unspecified
C220 (T203) — 143 hp
2.1 CDI — from 2001, end date unspecified
Engine code : unspecified
E220 (W210) — 136 and 143 hp
2.1 CDI — from 1995, end date unspecified
Engine code : unspecified
E220 (T210) — 143 hp
2.1 CDI — from 1996, end date unspecified
Engine code : unspecified
Additional technical specifications
Type: Hybrid Turbo
Turbo model: GT1852V
Engine: CDI
Documented power outputs: 116, 136, 143 and 146 hp
Fitting: No modifications required d’adaptation for compatible applications
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATIONBefore fitting, identify and rectify the cause of the previous failure. Check the oil supply and return d, the cleanliness of the lines, the intake and ensure there are no foreign objects. Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the part number on the original turbo das well as the OEM and manufacturer part numbers. Also check the model, generation, body style, engine type, power output,Year and engine code where available.
⚠️ Check your turbo’s part numbersBefore ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your turbocharger.