This hybrid turbo for, designed for the following engines Mercedes-Benz 2.7 CDI, features d an internal modification designed to adapt the d air flow.. Depending on the stage selected, it includes a high-flow MFS compressor wheel, reprofiled casings and, for the most comprehensive modification, a turbine wheel oversized.
It is intended for the C270, E270 and ML270 applications documented below. Its design allows for installation in the d'original location without any external modifications, provided that the part numbers are checked.
Available versions — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrustbearing: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor impeller in order d to adjust the compression capacity and d air flow rate, whilst retaining the mechanical configuration documented for in this stage.
Stage 2
Compressor impeller: MFS high-flow oversized
d intake housing: re-profiled for accommodate the new impeller
Thrustbearing: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The oversized impeller requires the intake housing to be re-profiled d. This combination aims to alter the compressor’s aerodynamic behaviour and its air-moving capacity.
Stage 3
Compressor impeller: MFS high-flow oversized
d ’s intake housing: re-profiled for to accommodate the new impeller
Thrustbearing: 360°
Turbine impeller: high flow oversized
Turbine housing: re-profiled for ly to accommodate the new impeller
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This version combines modifications to both the compressor and turbine sides. The result depends on the engine as a whole, the boost pressure and the settings applied; this configuration is therefore not automatically the most suitable for all applications.
What is a hybrid turbo?
A hybrid turbo features an architecture adapted for accommodate modified internal components. Depending on the tuning package, the modifications may involve the compressor wheel, the casings, the turbine wheel, the thrust bearing and the balancing.
The aim is d to adapt the compression capacity and air flow rate d. A hybrid turbo is not defined solely by the appearance of its impeller: the geometry of the components and the overall coherence of the assembly are crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in airflow d. A standard MFS wheel can retain a geometry equivalent to that d of the original.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. Depending on the specification, an impeller Performance may be designed with specific dimensions or a specific profile. Higher airflow can only be fully utilised with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air. Its diameter, profile, height, width and arrangement of its blades all influence its aerodynamic behaviour. The result also depends on the casings, the turbine, the boost pressure and the engine management system. A larger impeller does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbo
All three stages fe d a 360° stop, designed for to distribute axial forces more evenly. The rotor is balanced at high speeds, up to 150,000 rpm, on a Cimat VSR test bench to minimise vibrations and mechanical stresses. However, this balancing does not compensate for either a lack of lubrication or incorrect installation.
Engine remapping and preparation
Adjustments to the mapping and boost pressure control may be necessary for to make the most of the turbo’s characteristics. The fuel injection, exhaust, cooling, the clutch or the gearbox must also be checked depending on the level of tuning. The wastegate must be adjusted when remapping the ECU. Fitting d a hybrid turbo does not, on its own, guarantee a power gain.
Turbo part numbers
OEM part numbers
6120960292
6120960299
A612 096 0299
Manufacturer part numbers
709837-0001
709837-0002
709837-5001S
709837-5002S
Compatible vehicles and applications
Mercedes-Benz
C270 — 168 hp
2.7 CDI — from 1999, end date unspecified
Engine code : unspecified
E270 W210 — 170 hp
2.7 CDI — from 1995, end date unspecified
Engine code : unspecified
E270 T210 — 170 hp
2.7 CDI — from 1996, end date unspecified
Engine code : unspecified
ML270 163 — 163 hp
2.7 CDI — from 1997, end date unspecified
Engine code : unspecified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.7 CDI
Fuel: Diesel
Documented power outputs: 163, 168 and 170 hp
Installation: on the original d mounting, with no documented external modifications
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the oil supply and return lines d. Check that the lines are clean, the inlet and that there are no foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the turbo’s part number d, the original, OEM and manufacturer part numbers, as well as the model, generation, body style, engine type, power output,Year and engine code.. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number from your turbo.