This hybrid turbocharger is designed for the Mercedes C 320 3.0 CDI V6 with 224 hp from 2007 onwards. Its modification is based on a high-flow MFS compressor wheel Performance, a 360° bearing stop and high-speed balancing.
Three levels of tuning are documented. Each stage has its own dimensions and modifications to meet different performance objectives, without prejudging the engine’s final power output.
Available tuning packages — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS Performance high-flow
Dimensions: 43.40 / 56.03 mm
Blade configuration: 11+0 Performance design
Thrust bearing: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This configuration combines a high-flow MFS impeller with the. 360° bearing system. Its geometry is designed to match the compressor’ d ’ air displacement capacity whilst maintaining a ready-to-fit configuration.
Stage 2
Compressor impeller: MFS Performance high-flow oversized
Dimensions: 44.39 / 60.01 mm
Blade configuration: 11+0 Performance design
d intake housing: re-profiled for ly to accommodate the impeller oversized
Bearing: 360°
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 2 features a larger impeller and a re-profiled intake d housing. These modifications may promote a higher air flow d, with performance depending on the engine’s configuration and management system.
Stage 2+
Compressor impeller: MFS Performance high-flow oversized
Dimensions: 50.20 / 65.00 mm
Blade configuration: 11+0 Performance design
d intake housing: re-profiled for ly to accommodate the impeller oversized
Thrust bearing: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This version accommodates the largest compressor wheel of all documented configurations, as well as a modified intake d housing. Such a modification may alter the available flow rate, response time and optimal operating range.
What is a hybrid turbocharger?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate modified internal components. Depending on the stage, the modifications may involve the compressor wheel, its dimensions, the blade geometry, the housing, the thrust bearing or the balancing.
The aim is d to adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its impeller: the compatibility between its components and the engine’s tuning remains crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d. A standard MFS wheel may retain a geometry equivalent to that d of the original.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A Performance geometry may utilise a profile, diameter or blade configuration suited to the tuning objective.
Why does the blade geometry influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour. A suitable geometry can move more d'air under certain conditions, but the result also depends on the casings, the turbine, the boost pressure and the engine tuning. A larger impeller therefore does not automatically guarantee a better result and may alter the response time.
Reliability and balancing of the hybrid turbo
The 360° stop, documented at every stage, helps to distribute axial forces. The rotor is balanced at high speed, up to 150,000 rpm on a Cimat VSR test bench, in order to limit vibrations and mechanical stresses. However, this balancing does not compensate for faults in assembly or lubrication.
Engine remapping and preparation
The engine management system must be adapted for to make full use of the hybrid turbo’s characteristics. Depending on the level of tuning, the mapping, boost pressure, fuel injection, exhaust, cooling and transmission must be checked or adjusted. The wastegate must be adjusted during installation and when remapping the ECU. No power gain is automatic without a coherent configuration.
Turbo specifications
OEM part numbers
6420902980
642090608080
6420906080
6420902880
6420904680
642090288080
642090468080
Manufacturer’s part numbers
770895-7
770895-5007S
770895-0007
770895-2
770895-5002S
770895-0002
770895-8
770895-5008S
770895-0008
Compatible vehicles and assignments
Mercedes
C 320 CDI — 224 hp
3.0 CDI V6 — from 2007, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: turbo hybrid
Installation: plug & play, without any modifications to the vehicle
Engine: 3,.,0 CDI V6
Fuel: diesel
Power d Documented origin: 224 hp
Period: from 2007
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return lines d, the cleanliness of the pipes, as well as the inlet and ensure there are no foreign objects.
Carry out the priming procedure in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may result in further damage to the turbocharger.
How do you identify the correct turbo?
Check the part number marked on the turbo d'original, the OEM and manufacturer part numbers, as well as the model, engine type, power output, installation period and engine code. An identical engine type may be fitted with several different turbo configurations.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your turbocharger.