This hybrid turbo for engine 1.9 TDI 100 hp is available in three different preparation levels. Depending on the model chosen, its configuration combines a high-flow MFS compressor wheel, a 360° bearing stop and appropriate internal modifications.
It is intended for documented applications Seat, , Skoda and Volkswagen. Its design plug & play allows installation on the relevant assembly without any external modifications, provided that the part numbers are checked carefully d’origin’.
Available products — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: High-capacity MFS
Stop system: 360° bearing stop
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This preparation acts primarily on the compressor wheel in order to d’adjust the flow rate’ dair. The 360° stop helps to distribute the rotor’s axial forces more evenly.
Stage 2
Compressor wheel: High-capacity MFS oversized
Carter d’Admission:’ reprofiled for to accommodate the new wheel oversized
Stop system: 360° bearing stop
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 incorporates a compressor wheel oversized to a casing d’re-profiled intake’. This modification is intended to alter the compression capacity and flow rate d’air, without prejudging the engine’s ultimate power.
Stage 3
Compressor wheel: High-capacity MFS oversized
Carter d’Admission:’ reprofiled for to accommodate the new wheel oversized
Stop system: 360° bearing stop
Turbine wheel: high-speed oversized
Turbine casing: reprofiled for to accommodate the new wheel oversized
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This configuration includes modifications to the compressor and turbine sides. The size of the wheels and the reshaping of the casings alter the turbo’s aerodynamic behaviour; the result depends on the engine tuning and the conditions dUse.
What is a hybrid turbo ?
A hybrid turbo is based on a specially adapted turbocharger design for to receive internal components that differ from the configuration d’origin’. Depending on the service, the modifications may involve the compressor wheel, the casings, the turbine wheel, the thrust bearing system and balancing.
The aim is d’adjust the compression capacity and flow rate’ dair. However, a hybrid turbo is not defined solely by the appearance of its impeller: the geometry of its components and the overall coherence of the unit determine its performance.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process does not, on its own, guarantee an increase in throughput dair. A standard MFS wheel can retain a geometry equivalent to that d’origin’.
An MFS wheel Performance may be designed with a geometry suited to the application, in particular through its profile, blades or dimensions, where such modifications are envisaged. A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair.
A flow rate d’Increased air intake can enable the engine to produce more power when combined with appropriate engine tuning, although it does not, on its own, guarantee a power increase’.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades influence the aerodynamic behaviour of the compressor.
The right geometry can move more d’air under certain conditions’. The result also depends on the casings, the turbine wheel, the boost pressure and the engine management system. A larger wheel therefore does not automatically guarantee better performance and may affect response time as well as the range doptimal use.
Reliability and balancing of the hybrid turbocharger
The 360° bearing stop, which is featured in all three courses on offer, distributes axial forces over a wide surface area. It helps to adapt the bearing system to operational stresses, without making the turbocharger insensitive to faults in assembly or lubrication.
Every work placement offers d’high-speed balancing at 150,000 rpm on a Cimat VSR test bench’. The aim of this operation is to minimise vibrations and mechanical stresses on the rotor.
Engine remapping and tuning
Appropriate engine management is required for make the most of the hybrid turbo’s features. Depending on the level of preparation, it is advisable to check whether or d’adjust the mapping, boost pressure, fuel injection, exhaust and air cooling’ d’intake and transmission’. The wastegate must be adjusted when the ECU is remapped. The full configuration must be set up by a qualified professional.
Turbo part numbers
OEM part numbers
038253014B
038253016J
Manufacturer’s part numbers
54399700008
54399700019
54399800008
54399800019
54399880008
54399880019
54399900008
54399900019
Compatible vehicles and assignments
Seat
Córdoba 4 — 100 hp
1.9 TDI — from 2002, end date unspecified
Engine code : not specified
Ibiza 3 — 100 hp
1.9 TDI — from 2001, end date unspecified
Engine code : not specified
Skoda
Fabia — 100 hp
1.9 TDI — from 2000, end date unspecified
Engine code : not specified
Octavia 3 — 100 hp
1.9 TDI — from 2000, end date unspecified
Engine code : not specified
Roomster — 100 hp
1.9 TDI — from 2006, end date unspecified
Engine code : not specified
Volkswagen
Polo 7 — 100 hp
1.9 TDI — from 2001, end date unspecified
Engine code : not specified
Polo 8–100 hp
1.9 TDI — from 2005, end date unspecified
Engine code : not specified
Additional technical specifications
Product type: hybrid turbo
Engine: 1.9 TDI
Power : 100 hp
Editing: plug & play, with no documented external changes
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the supply and the return d’the oil and the cleanliness of all the pipes’.
Check the intake and ensure that no foreign objects can reach the compressor. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Make a note of the reference number marked on the turbocharger dthe original, then compare it with the OEM and manufacturer’s part numbers listed on this sheet. Also check the make, model, generation and engine type 1.9 TDI, the power of 100 hp, theYear the mounting code and the engine code, where available.
An identical engine does not necessarily guarantee compatibility: several configurations may coexist, depending on the vehicle version.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are unsure about your installation, please contact us with the reference number clearly visible on your turbo d’origin’.