This hybrid turbo, designed for the Volkswagen Crafter 2.5 TDI 109 hp, combines a mechanical installation requiring no modifications with internal tuning tailored to the selected package.. The documented configurations include a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
The various stages allow you to choose a configuration consistent with the engine project, ranging from improvements to the compressor wheel through to additional work on the turbine and its casings.
Available set-ups — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compression capacity and air flow rate d thanks to the high-flow MFS impeller. Its final performance depends on the engine management system and the vehicle’s overall configuration.
Stage 2
Compressor impeller: High-flow MFS oversized
d ’ intake housing: Reprofiled for accommodate the impeller oversized
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor wheel with a reprofiled d intake housing. This modification is designed to correctly accommodate the new wheel and utilise its flow potential as part d of a coherent engine tuning programme.
Stage 3
Compressor impeller: MFS high-flow oversized
Intake casing d: Reprofiled for to accommodate the impeller oversized
Thrustbearing: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine housing: Reprofiled for ly to accommodate the impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration complements the work carried out on the compressor side with a high-flow turbine impeller oversized and a re-profiled turbine housing. These modifications may affect the turbocharger’s flow rate and response; their benefits depend on the intended use and the selected settings.
What is a hybrid turbo?
A hybrid turbo retains a turbocharger architecture designed for to accommodate modified internal components. Depending on the upgrade stage, the modifications may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing or balancing.
The aim is d to adapt the compression capacity and air flow d to the requirements of the tuning. A hybrid turbo is not defined solely by the appearance of its impeller: the geometry, the machining of the housings and the overall balance of the unit are decisive.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone is not sufficient to achieve an increase in air flow d.
A standard MFS impeller may retain a geometry equivalent to that of the ori d. An MFS Performance impeller may be given a geometry adapted to the tuning, particularly in terms of its profile or dimensions, provided these modifications are documented.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. The data provided for for this product describe a forged aluminium impeller, which is lighter, larger and taller than the d'original, allowing for 15 per cent additional compression.
Why does the geometry of the blades influence the air flow d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and its ability to move air.
The result also depends on the casings, the turbine wheel, the boost pressure and the engine set-up. A larger wheel can alter the response time and the optimal operating conditions d; its size alone is therefore not sufficient to determine the turbo’s behaviour.
Reliability and balancing of the hybrid turbo
The documented 360° bearing thrust ring helps to distribute axial forces around the shaft. It must operate with correct lubrication and be fitted correctly.
The rotor is balanced at high speed, at 150,000 rpm on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not compensate for inadequate lubrication, contamination or incorrect fitting.
Engine remapping and preparation
Appropriate engine management is required for to make the most of the hybrid turbo’s characteristics. Fuel injection, exhaust, cooling and the engine control unit must be checked or adjusted according to the project. The wastegate must be adjusted during the reprogramming of the engine control unit. The clutch, the gearbox and other vehicle components must also be checked depending on the level of preparation.
Turbo specifications
OEM part numbers
076145701C
076145701CV
076145701CX
076145701D
076145701DX
076145701J
076145701JX
076145701K
076145701KX
076145701M
076145701MX
076145701P
076145701PX
076145702B
076145702BX
Manufacturer’s part numbers
49377-07420
49377-07421
49377-07422
49377-07423
49377-07424
49377-07425
49377-07426
49377-07430
49377-07432
49377-07460
Compatible vehicles and assignments
Volkswagen
Crafter — 2.5 TDI — 109 hp
2.5-litre engine TDI — from 2006, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.5 TDI
Power: 109 hp
Production period: From 2006, end not specified
Mechanical installation: No modifications required
Fitting instructions
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the oil supply and return lines d. Check that the pipes and inlet are clean and free from foreign objects.
Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the turbo part number d the original, OEM and manufacturer part numbers, as well as the make, model, engine type, power output, installation period and engine code. An identical engine type may have several different configurations.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, contact customer services with the part number clearly visible on your original turbocharger d.