This hybrid turbo for for the 3.0 DCI and 3.0 DXI engines, with power outputs of 156 or 160 hp, features dan internal modification designed to adapt its compression capacity and air flow d. Depending on the upgrade package chosen, the configuration includes a high-flow MFS compressor impeller, reprofiled casings and, at the most advanced level, a turbine impeller oversized.
The three documented modifications retain a design intended for an Installation without modification of the assembly. However, their use must be accompanied by da consistent engine modification programme tailored to the vehicle.
Available set-ups — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order dto adapt the air flow rate dto. The 360° thrust bearing helps to distribute the axial forces acting on the rotating assembly more evenly.
Stage 2
Compressor impeller: MFS high-flow oversized
d’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
oversized ’s compressor impeller is paired with a reprofiled intake casing d. This modification ensures dthat the new geometry fits correctly and may alter the compressor’s air displacement capacity d.
Stage 3
Compressor impeller: MFS high-flow oversized
d’ intake housing: Reprofiled for to accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration applies to both the compressor and turbine sides. Both housings are re-profiled for accommodate the oversized impellers, which may alter the flow rate as well as the behaviour of the turbocharger depending on its settings and operating conditions d’utilisation.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate internal components that differ from the original configuration d. Depending on the upgrade stage, modifications may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing system and balancing.
The aim is dto adapt the compression capacity and air flow rate dto a specific engine tuning. A hybrid turbo is therefore not defined solely by the appearance of its compressor wheel: the geometry of the wheels, the machining of the housings and the overall coherence of the unit are decisive.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process and does not, on its own, guarantee an increase in air flow rate d.
A standard MFS impeller may retain a geometry equivalent to that of the original d. An MFS impeller intended for a Performance conversion may adopt a different geometry depending on the desired outcome. For this product, the available data indicates a forged aluminium wheel that is lighter, larger and taller than the original d, with a claimed 15 per cent higher load capacity.
A standard MFS impeller can be just as efficient as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow can contribute to power output when the engine management system and peripheral equipment are suitably configured.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the amount dof air it can move under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine calibration. A larger impeller does not automatically guarantee a better result and may alter the response time or the optimal operating range.
Reliability and balancing of the hybrid turbo
All three stages are fitted dwith a 360° bearing stop, designed for to distribute axial forces over a wide surface area. It accommodates the stresses associated with turbocharger operation without protecting it dfrom installation or lubrication faults.
Each engine preparation includes dhigh-speed balancing at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor, but does not replace checks on the doil and dintake systems.
Engine remapping and tuning
The engine mapping and wastegate settings must be adjusted for to make the most of the hybrid turbo’s characteristics. Depending on the tuning, the dinjection, dexhaust, cooling and boost pressure management systems must also be checked or adjusted.
The clutch, gearbox and other vehicle components may also require inspection depending on usage. Fitting da hybrid turbo does not automatically guarantee a power increase without appropriate tuning.
Turbo specifications
OEM part numbers
14411DC001
14411DC00A
14411DC00B
Manufacturer part numbers
726372-0005
726372-0010
726372-0013
726372-5005S
726372-5010S
726372-5013S
Compatible vehicles and roles
Documented applications
3.0 DCI — 156 hp
Period and engine code not specified
3.0 DXI — 160 hp
Period and engine code not specified
No detailed allocation by make, model or generation is documented. Compatibility must be confirmed using the original turbo part number d.
Additional technical specifications
Product type: Hybrid Turbo
Part number family: 726372
Turbo model: GT2360V
Engine specifications: 3.0 DCI / 3.0 DXI
Power outputs: 156 hp / 160 hp
Installation: Intended configuration for installation without modification
Installation tips
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Carefully check the lubrication circuit, the oil supply and return d, as well as the cleanliness of all lines.
Check the inlet for any foreign objects. Prime the system in accordance with the applicable guidelines and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo dand compare it with the OEM and manufacturer part numbers in this data sheet.. Also check the make, model, generation, body style, engine type, power output at hp, the mountingYear and the engine code where available.
The same engine may be fitted with several different turbochargers depending on the vehicle version. The part number therefore remains the primary verification criterion.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this fact sheet. An identical engine does not always guarantee compatibility.
If in doubt, contact our team with the part number noted on your turbo.