This hybrid turbocharger is designed for the following engines: Hyundai and Kia CRDI as detailed in this data sheet. Depending on the upgrade package selected, the modification comprises a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
Applications include, in particular, the Hyundai, i20, i30 and ix35, as well as the Kia, Ceed and Soul. The level of preparation must be selected according to the engine configuration and intended use.
Available packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification acts on the compressor impeller to dadapt the air flow rate dwhilst maintaining the mechanical characteristics documented for this stage.
Stage 2
Compressor impeller: MFS high-flow oversized
Inlet casing d: re-profiled for accommodate the new impeller oversized
Bearing thrust ring: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The reprofiling of the casing allows dto fit the compressor impeller oversized. This configuration may alter the flow capacity and behaviour of the compressor depending on the associated engine set-up.
Stage 3
Compressor impeller: MFS high-flow oversized
d’ intake housing: re-profiled for accommodate the new impeller oversized
Bearing thrust ring: 360°
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This documented modification is carried out on both the compressor and turbine sides. Larger sizing may affect flow rate and response time; its operation depends on the overall engine configuration.
Understanding hybrid tuning
What is a hybrid turbocharger?
A hybrid turbo utilises a turbocharger architecture adapted for accommodate modified internal components. Depending on the upgrade stage, the modification may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing and balancing.
The aim is dadapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry of the parts and the overall coherence of the assembly are crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow d.
A standard MFS impeller may retain a geometry equivalent to that of the original d. A Performance MFS impeller may adopt a profile, dimensions or blade configuration tailored to the tuning objective, where such modifications are intended.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow rate can contribute to power output with a suitably adapted engine tuning, though it does not in itself guarantee results.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and arrangement of its blades all influence its aerodynamic behaviour. The result also depends on the housings, the turbine wheel, the boost pressure and the engine management system. A larger wheel therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing, documented for across all three stages, helps to distribute the axial forces exerted on the rotating assembly. It does not, however, d’replace the need for proper lubrication or d’correct installation.
High-speed balancing is carried out at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor, but does not protect against d’oil defects, contamination or incorrect installation.
Engine remapping and preparation
Operating da hybrid turbo may require adjustments to the mapping, boost pressure and wastegate setting. Depending on the level of tuning, the fuel injection, exhaust system, intake air cooling d, clutch or gearbox may also need to be checked and, where necessary, adjusted. Fitting the turbocharger alone does not guarantee a power increase.
Turbo part numbers
OEM part numbers
282012A700
28201-2A700
Manufacturer part numbers
775274-0002
775274-5002S
Compatible vehicles and applications
Hyundai
i20 — 1., 6 CRDI,110 hp,
Engine variants: 1., 6 CRDI — from 2008, enddate unspecified
,Engine code: unspecified
i30 — 1.6 CRDI 110 hp
Engine 1.6 CRDI — from 2008, end date unspecified
Engine code : unspecified
ix35 Slovakia — 1.7 CRDI 115 hp
Engine 1.7 CRDI — from 2010, end date unspecified
Engine code : unspecified
Kia
Ceed — 1.6 CRDI 110 hp
Engine 1.6 CRDI — from 2008, end date unspecified
Engine code : unspecified
Soul — 1.6 CRDI 110 hp
Engine 1.6 CRDI — from 2008, end date unspecified
Engine code : unspecified
Additional technical specifications
Product type: turbo hybrid
Documented engine variants: 1.6 CRDI and 1.7 CRDI
Documented power outputs: 110 hp and 115 hp depending on application
Documented production periods: from 2008 or 2010, depending on the vehicle
Engine codes: not specified
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return das well as the cleanliness of all pipes.
Check the inlet and ensure there are no foreign objects present. Carry out the priming procedure in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo d, the OEM and manufacturer part numbers, then compare the make, model, version, engine type, power output, mountingYear and engine code.. An identical engine type may be fitted with several different turbocharger configurations.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number taken from your turbocharger.