This hybrid turbocharger, designed for the Mitsubishi 2.5 TD 87 hp engine, undergoes internal modification to adapt the dair flow and the. compression capacity. Depending on the upgrade package selected, the modifications involve the MFS compressor wheel, the housings and, for the most comprehensive upgrade package, the turbine wheel.
The documented specification applies to the Mitsubishi L200 fitted with the 4D56-T engine, for for the period between November 1992 and August 1996. The configuration is designed for for an external Installation without modification of the original assembly d.
Available preparations — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust system: 360° bearing thrust
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR bench
This modification combines a high-flow MFS compressor wheel with a 360° thrust bearing. It is designed to alter the compression capacity and air flow rate dwhilst retaining the casings documented for for this modification.
Stage 2
Compressor impeller: MFS high-flow oversized
dintake housing: re-profiled for to accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 uses a oversized compressor wheel and a dintake housing, re-profiled. This combination allows dto adapt the air passage dto the new wheel, whilst also modifying the turbocharger’s response characteristics.
Stage 3
Compressor wheel: MFS high-flow oversized
d’ intake housing: re-profiled for to accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine housing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 3 combines modifications to the compressor side with a high-flow turbine wheel oversized and a re-profiled turbine housing. This configuration affects both sides of the turbocharger and requires engine preparation appropriate to its use.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted to accommodate internal components that differ from the original configuration d. Depending on the upgrade stage, the modifications may involve the compressor wheel, the housing profile, the turbine wheel, the thrust bearing system and balancing.
dThe aim is to adapt the compression capacity and air flow dto the requirements dof an engine tuning programme. A hybrid turbo is not defined solely by the appearance of its impeller: the geometry of the components, their fit within the housings and the overall balance of the unit are crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow d. A standard MFS wheel can retain a geometry close to the original.
An MFS impeller Performance can be designed with a geometry tailored to the tuning objective, particularly in terms of its profile, dimensions or blade configuration. On this product, the wheel shown is made of forged aluminium; it is lighter, larger and taller than the original d. The technical data provided indicates a 15 per cent higher compression capacity.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher flow rate can only be fully utilised with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour and the amount dof air it can move under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee better performance and may alter the response time or the range dof optimal operation.
Reliability and balancing of the hybrid turbo
The 360° bearing thrust ring, featured on all three documented stages, distributes axial forces over a suitable surface. It contributes to the mechanical integrity of the assembly without making the turbocharger immune to assembly or lubrication faults.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses during operation.
Engine remapping and preparation
The engine management system must be adapted for to make full use of the hybrid turbo’s characteristics. The wastegate must be adjusted during the ECU remapping.
Depending on the level of tuning, it is also advisable to check or d’adjust the fuel injection, exhaust system, cooling system, boost pressure and other components under load. Fitting d’a hybrid turbo alone does not guarantee a power gain.
Turbo specifications
OEM part numbers
MD194842
MR355223
MD194843
MR355222
DMX125023
Manufacturer’s part numbers
49177-01502
49177-01503
49177-01504
49177-01505
Compatible vehicles and applications
Mitsubishi
L200 (K3_T, K2_T, K1_T, K0_T) — 87 hp
2,.5, TD -diesel — 11/1992 to 08/1996
Engine code: 4D56-T
Additional technical specifications
Product type: hybrid turbo
Engine: 2.5 TD
Fuel: diesel
Power: 87 hp
Engine code: 4D56-T
Production period: 11/1992 to 08/1996
Installation: documented plug-and-play configuration
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the supply and the return lines das well as the cleanliness of all lines. Check the inlet and ensure there are no foreign objects present. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. An uncorrected lubrication fault may result in further turbocharger failure.
How do you identify the correct turbo?
Check the part number marked on the turbo dthe original, OEM and manufacturer part numbers, as well as the make, model, generation, engine type, power output, production period and engine code. An identical engine type may have several different configurations.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If you are unsure about identification or compatibility, please contact our team with the full part number of your turbocharger.