This hybrid turbocharger, designed for the following engines: Mitsubishi 1.8 DI-D 150 hp, combines a high-flow MFS compressor wheel Performance with a 360° bearing retainer.. Three specification levels are available to dadapt the turbocharger’s characteristics to the engine project.
Documented applications include the Mitsubishi ASX and Lancer produced between June 2010 and December 2015. Installation is designed to require no external modifications, subject to checking the part numbers and carrying out the necessary adjustments.
Available versions — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS Performance high-flow
Dimensions: 35.90 / 51.00 mm
Blade configuration: 4+4
Bearing stop: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification alters the compressor impeller to dadapt the flow rate dto the air, whilst retaining the mechanical characteristics specific to this stage.
Stage 2
Compressor impeller: MFS Performance high flow rate oversized
Dimensions: 41.93 / 55.69 mm
Blade configuration: 11+0
d’ intake housing: reprofiled for accommodate the impeller oversized
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a larger impeller with a reprofiled intake casing d. This combination is designed to optimise airflow and compression, with performance depending on the engine’s overall configuration.
Stage 2+
Compressor impeller: MFS Performance high-flow oversized
Dimensions: 46.02 / 58.00 mm
Blade configuration: 11+0
dintake housing: reprofiled for ly to accommodate the impeller oversized
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2+ uses a larger compressor impeller and a modified intake dhousing. A larger impeller alone does not guarantee better performance: the result depends on the tuning and the overall set-up.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for to accommodate internal components that differ from the original configuration d. Depending on the upgrade stage, modifications may involve the compressor wheel, its dimensions, the geometry of the blades, the intake housing d, the thrust bearing and the balancing.
The aim is d’to adapt the compression capacity and air flow d’to the requirements of the engine project. A hybrid turbo is not defined solely by the appearance of its impeller: consistency between the components, machining and settings is crucial.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow d. A standard MFS wheel can retain a geometry equivalent to that dof the original.
An MFS impeller Performance can be given a geometry tailored to the tuning objective, in particular a specific diameter, profile or blade configuration. A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air.
A higher airflow rate can help generate more power when the engine is suitably tuned, though it does not in itself guarantee a power gain.
Why does the geometry of the blades influence the air flow rate d?
The supercharger impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour. A suitable geometry can move more dair under certain operating conditions.
The result also depends on the compressor housing, the turbine section, the boost pressure and the engine set-up. Increasing the dimensions can alter the response time as well as the range dof optimal operation.
Reliability and balancing of the hybrid turbocharger
The 360° stop present on all three stages helps to distribute the axial forces exerted on the rotating assembly. It does not replace d’proper lubrication or d’correct installation.
Each engine preparation undergo dhigh-speed balancing at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor, without compensating for any faults in assembly, lubrication or dthe oil supply.
Engine remapping and preparation
Appropriate engine management may be required for to make the most of the hybrid turbo’s characteristics. Depending on the tuning package and the vehicle, it is advisable to check or d’adjust the mapping, boost pressure, fuel injection, exhaust system, intake air cooling dand other components under load.
The wastegate must be adjusted during installation and when reprogramming the ECU. A hybrid turbo does not automatically guarantee a power gain without appropriate preparation.
Turbo specifications
OEM part number
1515A185
Manufacturer’s part numbers
49335-01003
49335-01002
49335-01001
49335-01000
Compatible vehicles and applications
Mitsubishi
ASX 1.8 DI-D — 150 hp
Engine variants 1.8 DI-D — 06/2010 to 12/2015
Engine code: not specified
Lancer 1.8 DI-D –150 hp
Engine 1.8 DI-D — 06/2010 to 12/2015
Engine code: not specified
Additional technical specifications
Product type: turbo hybrid
Engine: Mitsubishi 1.8 DI-D
Power: 150 hp
Production period: 06/2010 to 12/2015
Installation: plug & play configuration, with no documented external modifications
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d, the cleanliness of the pipes, as well as the intake and ensure there are no foreign objects.
Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions. The wastegate must be adjusted during fitting and remapping.
An uncorrected lubrication fault may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the turbo’s part number d– the original, OEM and manufacturer’s part numbers, as well as the model, engine type 1.8 DI-D, power output 150 hp and installation period.. The generation, body style and engine code must also be compared where available.
An identical engine specification does not always guarantee compatibility between two set-ups.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If you are unsure about the identification or fitment, please contact us before ordering.