This hybrid turbo for, designed for the Volkswagen 2.5 TDI, is based on an internal modification designed to adapt the air flow dand the compression capacity.. Depending on the upgrade package selected, it is fitted with a high-flow MFS compressor wheel, a 360° thrust bearing and reprofiled housings.
It is designed for LT 2 and LT 3 Volkswagen s within the power ratings and installation periods documented below. Its design plug & play allows for Installation without modification of the original layout d.
Available versions — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing: 360° thrust
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor impeller in order dto adapt the flow rate dto the air, whilst retaining a configuration closer to the original ddesign.
Stage 2
Compressor wheel: MFS high-flow oversized
d’ intake housing: re-profiled for accommodate the new impeller
Bearing: 360° thrust
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The oversized impeller requires the intake housing to be re-profiled d. This combination aims to increase the compressor’s air displacement capacity d, with performance depending on the engine configuration and mapping.
Stage 3
Compressor impeller: MFS high-flow oversized
Intake housing d: re-profiled for to accommodate the new impeller
Bearing: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification applies to both the compressor and turbine sides. The increased dimensions and reprofiling of both housings alter the flow conditions and may also affect the turbocharger’s response time.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for accommodate internal components that differ from the original dconfiguration. Depending on the stage, the modification may involve the compressor wheel, the turbine wheel, the housings, the thrust bearing system and balancing.
The aim is dto adapt the compression capacity and the air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry of the wheels and the overall coherence of the unit are decisive.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process and, on its own, is not sufficient to prove an increase in air flow d.
A standard MFS impeller may retain a geometry equivalent to the original. An MFS impeller Performance can be given a profile and dimensions tailored to the tuning objective. On this product, the impeller shown is made from forged aluminium and features a configuration that is lighter, larger and taller than the doriginal.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow can help generate more power when the engine is properly tuned, though this alone does not guarantee results.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour. A suitable geometry can move more dair under certain conditions, but the result also depends on the casings, the turbine wheel, the boost pressure and the engine management system. A larger wheel therefore does not automatically guarantee a better result and may alter the response time.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing fitted to each stage distributes axial forces over a wide surface area. It helps the bearing adapt to the stresses of the modification without making the turbo immune to faults in assembly or lubrication.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses during operation.
Engine remapping and preparation
Appropriate engine management is required for to make the most of the hybrid turbo’s characteristics. The mapping, boost pressure and wastegate setting must be checked during reprogramming. Depending on the tuning, the fuel injection, exhaust, cooling, intake and transmission may also require checking or adjustment.
Turbo specifications
OEM part numbers — Volkswagen
074 145 701C
074145701C
Manufacturer part numbers
53149707025
53149807025
53149887025
53149907025
K14-7025
Compatible vehicles and assignments
Volkswagen
LT 2 2.5 TDI — 83, 90, 95 and 102 hp
Engine: 2.5 TDI — from 1996, end date unspecified
Engine codes: unspecified
LT 2 2.5 TDI — 95 and 102 hp
Engine specifications: 2.5 TDI — from 1996, end date unspecified
Engine codes: unspecified
LT 3 2.5 TDI — 83 and 95 hp
Engine specifications: 2.5 TDI — from 2003, end date unspecified
Engine codes: unspecified
LT 3 2.5 TDI — 95 hp
Engine specifications: 2.5 TDI — from 2003, end date unspecified
Engine codes: unspecified
Additional technical specifications
Product type: turbo hybrid
Engine: 2...5 TDI
displacement: 2.5 l
Documented power outputs: 83, 90, 95 and 102 hp
Installation: plug & play, without modification to the layout
Engine codes: not specified
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d’installing the turbo. Check the lubrication system, the oil supply and return d’as well as the cleanliness of the pipes.
Check the intake for foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further damage to the turbocharger.
How do you identify the correct turbo?
Check the part number marked on the original turbo d, the OEM and manufacturer part numbers, as well as the make, model, generation, engine type, power output, installation period and engine code.. An identical engine may be fitted with several different turbo set-ups.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, contact our team with the full part number taken from your turbocharger.