This hybrid turbocharger Stage 1, Stage 2 or Stage 3 is designed for 2.5- DCI/CDTI engines with power outputs of 100, 120 and 146 hp, corresponding to the part numbers listed on this data sheet. Its design features, in particular, a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing on a Cimat VSR test bench.
The configuration is designed for for an external Installation without modification. The level of tuning should be selected according to the vehicle’s intended use and the planned modifications to the engine management system, fuel injection, exhaust and cooling systems.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order dto adjust the compression capacity and dair flow, whilst maintaining a configuration suitable for the intended installation.
Stage 2
Compressor impeller: MFS high-flow oversized
dIntake casing: re-profiled for accommodate the new impeller oversized
Thrust bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a dintake housing that has been re-profiled. This modification is designed to adapt the airflow to the compressor’s new geometry.
Stage 3
Compressor impeller: MFS high-flow oversized
dintake housing: re-profiled for to accommodate the new impeller oversized
Thrust bearing: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 3 modifies the compressor and turbine sides. The combination of oversized impellers and re-profiled housings enab d’s turbocharger to adapt its operation to a more comprehensive engine upgrade, though this alone does not guarantee the final power output.
What is a hybrid turbo?
A hybrid turbo uses a turbocharger design adapted for to accommodate modified internal components. Depending on the stage of the upgrade, modifications may involve the compressor wheel, the turbine wheel, the housings, the thrust bearing and the rotor balancing.
The aim is dto adapt the compression capacity and air flow rate d. However, the result depends on the overall configuration: impeller geometry, housings, boost pressure and engine settings. The appearance of the compressor impeller is therefore not sufficient to define the performance dof a hybrid turbo.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow d. A standard MFS wheel can retain a geometry equivalent to that dof the original.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. On this product, the documented MFS impeller is lighter, larger and taller than the d’original impeller; it is claimed to provide 15 per cent more compression. To make the most of this capability, appropriate engine tuning is required.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour. A suitable geometry can move more dair under certain conditions, but a larger impeller does not automatically guarantee better performance and may alter the response time. The result also depends on the casings, the turbine, the boost pressure and the engine mapping.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing distributes axial forces around the turbo’s axis. The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench to minimise vibrations and mechanical stresses. This balancing does not protect against incorrect installation, contamination or inadequate lubrication.
Engine remapping and preparation
The engine management system must be adapted for to make full use of the hybrid turbo’s characteristics. This involves adjusting the mapping, boost pressure, injection, air cooling d, the intake, the exhaust and, depending on the vehicle, the clutch or transmission must be checked.. The wastegate must be adjusted when remapping the ECU.. The turbo alone does not guarantee any specific power output.
Turbo specifications
OEM manufacturer part numbers
8.200.433.479D
8.200.683.866
8.200.766.765A
8.200.879.731
8200433479D
8200683866
8200766765A
8200879731
Manufacturer’s part numbers
757349-0001
757349-0002
757349-0003
757349-0004
757349-5001S
757349-5002S
757349-5003S
757349-5004S
GT1549S
Compatible vehicles and assignments
Fits to be verified
Documented engine specifications: 2.5 DCI/CDTI — 100, 120 and 146 hp
No specific make, model, production period or engine code is documented. Compatibility must be confirmed using the reference number of the original turbo d.
Additional technical specifications
Product type: hybrid turbo
Turbo family: GT1549S
Main part number: 757349
Engine: 2.5 DCI/CDTI
Specified power outputs: 100, 120 and 146 hp
Fitting: external Installation without modification
Fitting instructions
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the oil supply and return d. Check that the pipes are clean, the inlet and that there are no foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the part number engraved on the turbo dthe original, OEM and manufacturer part numbers, as well as the vehicle’s make, model, generation, body style, engine type, power output,Year and engine code. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility. If in doubt, please contact us before placing your order.