This hybrid turbo is designed for the 3.0 CDTI / DCI engines with 136 and 140 hp. Depending on the tuning package chosen, the kit combines a high-flow MFS compressor wheel, a 360° bearing stop and internal modifications tailored to the tuning level.
Its configuration plug & play is designed for to allow for an external Installation without modification of the assembly d'original. An adaptation of the engine management system and peripheral systems remains necessary for to utilise its characteristics correctly.
Available tuning kits — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: high-flow MFS
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order d to adjust the compression capacity and d the air flow. It retains a different configuration from the stages incorporating oversized impellers.
Stage 2
Compressor impeller: MFS high-flow oversized
d' intake housing: Reprofiled for accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
oversized ’s compressor impeller requires the intake housing to be re-profiled d. This combination can increase air displacement capacity d, with performance that also depends on engine tuning and operating conditions d.
Stage 3
Compressor wheel: High-flow MFS oversized
Intake housing d: Reprofiled for to accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine housing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification alters the compressor and turbine sides. Both housings are re-profiled for to accommodate the corresponding oversized impellers, which adapts the air and exhaust gas flow capacities d without guaranteeing a specific final power output.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger design adapted for to incorporate internal components that differ from the original configuration d. Depending on the stage of the upgrade, the modifications may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing system and balancing.
The aim is d to adapt the compression capacity and the d air flow. However, a hybrid turbo is not defined solely by the appearance of its impeller: the overall geometry, machining and balancing must all be taken into account.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d'air. A standard MFS wheel can retain a geometry similar to the d'original.
An MFS impeller Performance can be given a geometry adapted to the tuning programme – such as blade profile, height or width, diameter or specific configuration – only where these characteristics are specified for for the product. On this turbo, the impeller shown is a high-flow MFS impeller, oversized for Stages 2 and 3.
A standard MFS impeller can perform just as well as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher flow rate can contribute to power output with appropriate engine tuning, though it does not in itself guarantee results.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the amount d of air it can move under certain conditions.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine calibration. A larger impeller is therefore not automatically more efficient in all situations and may alter the turbo’s response time.
Reliability and balancing of the hybrid turbo
The 360° bearing thrust ring, present on the three documented stages, helps to distribute the axial forces borne by the rotating assembly. It does not replace d'proper lubrication' or d'correct installation'.
The rotor is balanced at high speed, up to 150,000 rpm on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not protect the turbocharger against a fault d in the oil supply, a foreign object or incorrect installation.
Engine remapping and preparation
The engine mapping and boost pressure control must be adjusted for to make the most of the turbo’s characteristics. The wastegate must be adjusted when remapping the ECU.
Depending on the tuning, it is also advisable to check or d'adjust the fuel injection, exhaust, cooling, intake and, if necessary, the transmission. Fitting d'a hybrid turbo does not automatically guarantee a power gain without appropriate tuning.
Turbo specifications
Manufacturer’s or comparative part numbers
14411DB00A
7.701.065.204
7701065204
Manufacturer’s part numbers
H12-22
HT12-22A
HT12-22B
HT12-22C 047-00A
HT12-22D
Compatible vehicles and roles
Documented applications
3.0 CDTI / DCI engines — 136 and 140 hp
Models, production periods and engine codes not specified.
Additional technical specifications
Product type: Hybrid Turbo
Engine: 3.0 CDTI / DCI
Power: 136 / 140 hp
Installation: Configuration plug & play, with no documented external modifications
Engine code: Not specified
Fitting period: Not specified
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbo.
dCheck the lubrication system, the oil supply and return lines, and ensure all lines are clean. Also check the intake for any foreign objects.
Prime the turbocharger in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may lead to the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo d and compare it with the manufacturer’s and supplier’s part numbers in this data sheet. Also check the make, model, generation, body style, engine type, power output at hp, the production period and the engine code where available.
An apparently identical engine may be fitted with several different turbo set-ups. The part number for the original equipment d therefore remains the key element to check.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine does not always guarantee compatibility.
If in doubt, please contact us with the full part number taken from your turbo.