This hybrid turbocharger, designed for the engine Nissan 2.5 DI-D The YD25DDTI is based on an internal design combining a high-flow MFS compressor wheel, a 360° bearing thrust ring and high-speed balancing. Three levels of preparation are available so that d’adapt the turbocharger’s specifications to the engine design’.
The documented assignments relate in particular to Nissan Navara NP300 D40 and Pathfinder III R51. Compatibility must always be confirmed using the turbo’s part number d’origin’.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: High-capacity MFS
Dimensions: 41.55 / 56.03 mm
Blade configuration: 11+0, design Performance
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This unit uses an MFS compressor wheel designed for adjust the flow rate d’air, whilst retaining the dimensions and modifications specific to this Stage 1.
Stage 2
Compressor wheel: High-capacity MFS oversized
Dimensions: 47.50 / 60.01 mm
Blade configuration: 11+0, design Performance
Carter d’Admission:’ reprofiled for to receive the wheel oversized
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The larger diameter of the wheel requires the casing to be re-profiled d’admission’. This combination is designed to alter the ability to move d’compressor air, with behaviour depending on the engine’s overall configuration’.
Stage 2+
Compressor wheel: High-capacity MFS oversized
Dimensions: 50.20 / 65.00 mm
Blade configuration: 11+0, design Performance
Carter d’Admission:’ reprofiled for to receive the wheel oversized
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This version features the largest documented Ferris wheel for this product and a casing d’adapted admission’. An increase in size may affect the flow rate d’air, response time and range doptimal use; it must therefore be selected according to the engine design.
What is a hybrid turbo ?
A hybrid turbo retains an architecture suited to the intended installation whilst undergoing targeted internal modifications. Depending on the course, these may cover the compressor wheel, its dimensions, the geometry of the blades, the re-profiling of the housing, the thrust bearing or balancing.
The aim is d’adjust the compression capacity and flow rate’ dturbocharger air. A hybrid turbo is not defined solely by the appearance of its impeller: its mechanical and aerodynamic performance depends on all its components.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process does not, on its own, guarantee an increase in throughput dair. A standard MFS wheel can retain a geometry equivalent to that d’origin’.
An MFS wheel Performance can be designed with a geometry suited to the intended application, for example a specific profile, diameter or blade configuration, provided that these details are documented.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. A higher flow rate can only lead to an increase in power if accompanied by appropriate engine tuning.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the amount dthe volume of air it can displace under certain conditions.
The result also depends on the compressor housing, the turbine section, the boost pressure and the engine tuning. A larger wheel is therefore not automatically more suitable for every application and may affect response time.
Reliability and balancing of the hybrid turbocharger
The 360° stop fitted to all three stages helps to distribute the axial forces acting on the rotating assembly. It does not exempt d’proper lubrication nor d’a compliant installation’.
Every documented preparation benefits from d’high-speed balancing at 150,000 rpm on a Cimat VSR test bench’. The aim of this operation is to minimise vibrations and mechanical stresses on the rotor, without compensating for a fault d’installation or doil supply.
Engine remapping and tuning
It may be necessary to adjust the engine management system for make the most of the hybrid turbo’s features. Mapping, boost pressure, fuel injection, air cooling d’The intake, exhaust and transmission must be checked in accordance with the level of preparation’. The wastegate must be adjusted during fitting and remapping. No increase in power is automatic without the appropriate configuration.
Turbo part numbers
OEM part numbers
14411EC00C
14411EC00B
14411EC00E
Manufacturer’s part numbers
769708-0001
769708-0002
769708-0003
769708-0004
769708-1
769708-2
769708-3
769708-4
769708-5003S
769708-5004S
Compatible vehicles and assignments
Nissan
Navara NP300 (D40) PC — 144 hp
Diesel — from July 2005, end date unspecified
Engine code : YD25DDTI
Navara NP300 (D40) PC — 171 hp
Diesel — from October 2006, end date unspecified
Engine code : YD25DDTI
Navara NP300 (D40) PC — 174 hp
Diesel — from July 2005, end date unspecified
Engine code : YD25DDTI
NP300 Navara (D40) PC — 163 hp
Diesel — from October 2006, end date unspecified
Engine code : YD25DDTI
Pathfinder III (R51) PC — 171 hp
Diesel — from October 2006, end date unspecified
Engine code : YD25DDTI
Pathfinder III (R51) PC — 174 hp
Diesel — from January 2005 to January 2010
Engine code : YD25DDTI
Additional technical specifications
Product type: hybrid turbo
Engine: Nissan 2.5 DI-D
displacement : 2.5 l
Fuel: diesel
Documented power ratings: 144, 163, 171 and 174 hp
Engine code : YD25DDTI
Mounting configuration: plug & play, unchanged d’adaptation’
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the supply and the return d’oil, as well as the cleanliness of the pipes.
Check the intake and ensure there are no foreign objects. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions. The wastegate adjustment and mapping must be adapted to the installation.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger dthe original, then compare the OEM and manufacturer part numbers. Also check the make, model, generation, engine type and power output in hp, the assembly period and the engine code. Having the same motor does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact us with the full part number from your turbocharger.