This hybrid turbo is designed for the following engines Nissan 2.5 TD with power outputs of 103 hp. Its specification combines a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing, with additional modifications depending on the chosen performance stage.
The three documented levels allow you to select a configuration suited to the engine project, without specifying a final power output. Installation is designed for the plug & play configuration, without any external modifications d'installation.
Available set-ups — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor side in order d to adapt the compression capacity and the air flow rate d. The 360° thrust bearing contributes to a better distribution of axial forces.
Stage 2
Compressor impeller: MFS high-flow oversized
d intake housing: re-profiled for accommodate the new impeller oversized
Thrust bearing: 360° thrust bearing
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 2 combines a oversized compressor impeller with a reprofiled d intake housing. This combination is designed to adapt the airflow to the new geometry, with performance that also depends on the mapping and the engine as a whole.
Stage 3
Compressor impeller: MFS high-flow oversized
Casing d Inlet: reprofiled for to accommodate the new impeller oversized
Thrust bearing: 360° thrust bearing
Turbine impeller: high-flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration includes modifications to the compressor and turbine sides. Resizing the impellers and re-profiling the housings can alter both flow rate and response time; the result depends on the overall engine tuning.
What is a hybrid turbo?
A hybrid turbo retains a turbocharger architecture designed for accommodate modified internal components. Depending on the stage, the modification may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing and the balancing.
The aim is d to adapt the compression capacity and air flow rate d to the requirements of the project. A hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry of the components and their mechanical adaptation are crucial.
MFS compressor impeller: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d. A standard MFS wheel may retain a geometry equivalent to that d of the original.
An MFS wheel Performance can be given a geometry tailored to the tuning objective. For this product, the data indicate a wheel that is lighter, larger and taller than the d original, with a compression capacity claimed to be 15 per cent higher.
A standard MFS impeller can perform just as well as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher airflow can only be fully utilised with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor wheel draws in and then compresses the air destined for the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour. A suitable geometry can move more d air under certain conditions, but the result also depends on the casings, the turbine, the boost pressure and the mapping. A larger impeller therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces over a suitable surface. The rotor is balanced at high speeds, up to 150,000 rpm, on a Cimat VSR test bench to minimise vibrations and mechanical stresses. However, this balancing does not compensate for faults in assembly, lubrication or d the oil supply.
Engine remapping and preparation
The engine control unit must be adapted for to make full use of the hybrid turbo’s characteristics. Depending on the project, the injection, exhaust, cooling, boost pressure and the transmission may need to be checked or adjusted. The wastegate must be adjusted when the ECU is remapped. The turbo alone does not guarantee any increase in power.
Turbo specifications
Manufacturer’s part numbers Nissan
14411-3S900
144113S900
Manufacturer and comparison part numbers
047-116
047-116 HT1018
1047116
HT10-18
HT10-18 047-116
HT10-18-R
HT1018R
N809N66
Compatible vehicles and roles
Nissan
Model unspecified — 2.5 TD — 103 hp
Engine variants: 2,., 5, TD — period unspecified
Engine code: unspecified
Additional technical specifications
Product type: turbo hybrid
Engine: Nissan 2.5 TD
Power: 103 hp
Fitting: plug & play configuration, no external modifications required d'installation
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return d, the cleanliness of the pipes, and the inlet, ensuring there are no foreign objects. Carry out priming in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the part number marked on the turbo d the original part number, the manufacturer’s and supplier’s part numbers, as well as the make, model, engine type, power output, installation period and engine code. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, contact our team with the full part number taken from your turbocharger.