This hybrid turbocharger, designed for the 1.4 CRDTI engine, is available in three performance levels. Depending on the level chosen, the modifications relate to the MFS compressor wheel, the housings, the turbine wheel, the bearing thrust ring and the rotor balancing.
plug & play ’s design allows for Installation without modification of the original layout d. However, to make full use of its capabilities, the engine must be tuned in a way that is consistent with and suited to the vehicle.
Available tuning options — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing retainer: 360°
Balancing: high-speed at 150,000 revolutions per minute on a Cimat VSR test bench
This modification primarily affects the compressor section in order d to adjust the compression capacity and air flow rate d whilst retaining the documented configuration of Stage 1.
Stage 2
Compressor impeller: MFS high-flow oversized
d' intake housing: re-profiled for accommodate the new impeller oversized
Bearing thrust ring: 360°
Balancing: high-speed at 150,000 revolutions per minute on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a d intake housing, re-profiled. This modification is designed to correctly accommodate the new geometry and to enhance the compressor’s performance.
Stage 3
Compressor impeller: MFS high-flow oversized
d intake housing: re-profiled for to accommodate the new impeller oversized
Bearing thrust ring: 360°
Turbine impeller: high flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 revolutions per minute on a Cimat VSR test bench
Stage 3 includes modifications to the compressor and turbine sides. The larger impeller dimensions and the re-profiling of the housings may alter the air flow rate d, gas flow rate and response time depending on the engine configuration.
What is a hybrid turbo?
A hybrid turbo is based on an architecture designed for to accommodate internal components that differ from the original configuration d. Depending on the upgrade stage, the modification may involve the compressor wheel, the turbine wheel, the housings, the thrust bearing and balancing.
The aim is d to adjust the compression capacity and the air flow rate d. A hybrid turbo is not defined solely by the appearance of its wheel: the geometry of the components and how they are combined determine its behaviour.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in air flow rate d.
A standard MFS impeller may retain a geometry equivalent to that of the ori d. An MFS Performance impeller may adopt a geometry adapted to the modification, particularly in terms of its profile, dimensions or the shape of its blades, where such modifications are intended.
A standard MFS impeller can be just as glossy as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher airflow rate can contribute to an increase in power with appropriate engine tuning, though this alone does not guarantee a specific result.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement all influence its aerodynamic behaviour. The result also depends on the casings, the turbine wheel, the boost pressure and the engine management system. A larger wheel therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbo
The documented 360° bearing stop helps to distribute axial forces over a wider surface area. However, it does not replace d the need for proper lubrication or d correct installation.
The rotor is balanced at high speed, at 150,000 revolutions per minute on a Cimat VSR test bench, to minimise vibrations and mechanical stresses. This balancing does not protect the turbocharger against insufficient lubrication, contamination or incorrect installation.
Engine remapping and preparation
The engine map must be adapted for to make the most of the hybrid turbo’s characteristics. Fuel injection, exhaust, cooling, pressure management and the transmission must be adjusted according to the level of tuning. The wastegate must be adjusted during the ECU remapping.
Turbo specifications
Manufacturer’s part numbers
755925-0001
755925-5001S
OEM Reference
17201-0N020
Compatible vehicles and applications
No specific vehicle applications are documented. Compatibility must be confirmed using the original turbo part numbers d and the vehicle’s specifications.
Additional technical specifications
Product type: Hybrid Turbo
Engine type: 1.4 CRDTI
Turbo model: GT1444V
Installation: Plug & play, no modification to the original d layout required
Fitting instructions
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous failure. Check the lubrication circuit, as well as the oil supply and return lines d. Ensure the pipes and inlet are clean and free from foreign objects.
Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions. A lubrication fault that is not rectified may lead to further damage to the turbocharger.
How do you identify the correct turbo?
Check the part number of the original turbo d, the OEM and manufacturer part numbers, as well as the make, model, generation, body style, engine type, power output, years of manufacture and engine code. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this product description. An identical engine specification does not always guarantee compatibility. If in doubt, please contact us before placing your order.