This twin-turbo hybrid is designed for the Range Rover Sport fitted with the 3.6 TDV8 engine producing 272 hp. The tuning package comprises high-flow MFS compressor wheels, a 360° bearing stop and high-speed balancing on a Cimat VSR bench.
Three levels of tuning are documented at. The modifications vary depending on the package chosen and may involve the compressor wheel, the housings and the turbine wheel.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order d to adjust the compression capacity and d the air flow rate. It retains a mechanical configuration closer to the basic design than the subsequent stages.
Stage 2
Compressor impeller: MFS high-flow oversized
d' intake housing: Reprofiled for accommodate the new impeller oversized
Bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a reprofiled d intake housing. This modification is designed to ensure the mechanical compatibility of the impeller and to improve the compressor’s performance.
Stage 3
Compressor impeller: MFS high-flow oversized
d intake housing: Reprofiled for to accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 3 includes modifications to the compressor and turbine sides. The sizing and reprofiling of the housings must remain consistent with the engine configuration and the turbocharging management system.
What is a hybrid turbocharger?
A hybrid turbo is based on a turbocharger architecture adapted for accommodate internal components that differ from the original configuration d. Depending on the stage, modifications may involve the compressor wheel, the intake housing d, the turbine wheel, the turbine housing, the thrust bearing system and balancing.
The aim is d'to adapt the compression capacity and the air flow rate d'. A hybrid turbo is not defined solely by the appearance of its impeller: the geometry of the components, their combination and the quality of the machining are decisive factors.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in airflow d. A standard MFS wheel may retain a geometry equivalent to that d of the original.
An MFS wheel Performance can be designed with a geometry suited to the engine build. On this product, the wheel shown is made of forged aluminium; it is lighter, larger and taller than the original wheel d. The specification sheet indicates an additional compression capacity of 15 per cent, the utilisation of which depends on the engine’s configuration and tuning.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air.
Why does the geometry of the blades influence the d air flow?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence its aerodynamic behaviour and the volume d of air it can move under certain conditions.
The result also depends on the casings, the turbine wheel, the boost pressure and the engine tuning. A larger wheel does not automatically guarantee better performance and may alter the response time as well as the range d'of optimal operation.
Reliability and balancing of the hybrid turbo
The documented 360° bearing thrust ring helps to distribute the axial forces exerted on the rotating assembly. It must operate with correct lubrication and does not protect the turbocharger against incorrect installation or insufficient oil supply.
Each stage includes high-speed balancing at 150,000 rpm on a Cimat VSR test bench. This operation aims to minimise vibrations and mechanical stresses on the rotor.
Engine remapping and preparation
Appropriate engine management is required for to make the most of the hybrid turbo’s characteristics. The mapping, injection, exhaust, cooling and boost pressure management must be checked or adjusted according to the level of tuning. The wastegate must be adjusted when reprogramming the ECU. The transmission and other vehicle components must also be checked in line with the chosen configuration.
Turbo part numbers
OEM part numbers — left-hand side
54399700063
54399700112
54399800063
54399800112
54399880063
54399880112
54399900063
54399900112
OEM part numbers — right-hand side
54399700062
54399700111
54399800062
54399800111
54399880062
54399880111
54399900062
54399900111
Manufacturer’s part numbers — left-hand side
6H306K682-FE
6H3Q6K682FC
Manufacturer’s part numbers — right-hand side
6H4Q6K682GD
6H4Q6K682GG
6H4Q6K682GH
LR004039
LR004526
LR02145
Compatible vehicles and allocations
Land Rover
Range Rover Sport — 3,.6, TD — 272 hp
3.6 TDV8 engine — from 2005, month unspecified — end unspecified
Engine code: not specified
Additional technical specifications
Product type: Twin-turbo hybrid
Configuration: Left-hand drive and right-hand drive
Engine: 3.6 TDV8
Power Documented: 272 hp
Installation: Plug & play, no modifications required d' installation
Engine code: Not specified
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d'installing the turbos.
Check the lubrication system, the oil supply and return lines d, and ensure all lines are clean.
Check the intake and ensure there are no foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number engraved or marked on each original turbo d, then compare it with the OEM and manufacturer part numbers in this fact sheet.. Also check the make, model, generation, engine type, power output,Year, and the engine code where available. An identical engine specification does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this specification sheet. An identical engine specification does not always guarantee compatibility.
If you are unsure whether it is the left-hand or right-hand side, please contact us with the part numbers taken from the original turbos d.