This hybrid turbocharger for, designed for a 2.5- TD engine, is available in three performance levels. It features a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing carried out on a Cimat VSR test bench.
It is designed for for installation plug & play without any modification to the mounting interfaces. However, to make full use of its performance characteristics, d appropriate engine tuning is required.
Available tuning options — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor impeller in order d'to adapt the flow rate d'to the air. No modifications to the casing or turbine impeller are documented for this modification.
Stage 2
Compressor impeller: MFS high-flow oversized
Compressor housing: re-profiled inlet for accommodate the new impeller oversized
Bearing thrust: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
The reprofiling of the housing allows d to accommodate the compressor impeller oversized. This configuration may alter the flow capacity and behaviour of the compressor depending on the engine settings.
Stage 3
Compressor impeller: MFS high-flow oversized
Compressor housing: inlet re-profiled for accommodate the new impeller oversized
Bearing thrust ring: 360°
Turbine impeller: high flow oversized
Turbine housing: reprofiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This preparation combines modifications to both the compressor and turbine sides. The turbine impeller oversized and its re-profiled housing influence the overall operation of the turbocharger; however, the final power output cannot be determined without knowing the engine’s full configuration.
What is a hybrid turbo?
A hybrid turbo retains an architecture suited to the interfaces of the specific turbocharger whilst incorporating internal modifications. Depending on the upgrade package, these may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing or balancing.
The aim is d to adapt the compression and air flow d to a specific tuning programme. A hybrid turbo is therefore not defined solely by the appearance of its compressor wheel, but by the consistency of its geometry, components and machining.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process and does not, on its own, guarantee an increase in air flow d. A standard MFS wheel may retain a geometry equivalent to that d of the original.
The MFS Performance wheel used in this build is described as a forged aluminium wheel, which is lighter, larger and taller than the d'original. The technical specification indicates a 15 per cent increase in compression capacity, though this does not constitute a guarantee of increased engine power.
A standard MFS impeller can be just as efficient as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher flow rate can only be utilised with a coherent engine tuning programme.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour and its ability to move air within certain operating ranges.
The result also depends on the housings, the turbine wheel, the boost pressure and the engine management system. A larger wheel does not automatically guarantee better performance and may alter the response time as well as the optimal operating range d.
Reliability and balancing of the hybrid turbo
The 360° bearing stop helps to distribute the axial forces applied to the rotor more evenly. It does not eliminate the need d for proper lubrication or compliance with installation conditions.
Each documented batch undergo d high-speed balancing at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor, but does not protect against incorrect installation, inadequate lubrication or the presence d of a foreign object.
Engine remapping and preparation
The engine mapping must be adapted for to make full use of the characteristics of this hybrid turbocharger. The injection, exhaust, cooling, boost pressure and the transmission must be checked or adjusted according to the configuration. The wastegate must be adjusted when the ECU is remapped. No power gain can be guaranteed without a complete and properly tuned set-up.
Turbo part numbers
OEM part numbers
2245241
22458381
Manufacturer part numbers
49177-06430
49177-06432
Compatible vehicles and applications
Fits to be verified
No specific make, model or production period is documented. Compatibility must be established based on the original turbocharger part numbers d.
Additional technical specifications
Product type: Hybrid Turbo
Engine capacity: 2.5 TD
Stated power outputs: 110 hp, 136 hp
Installation: plug & play, without modification to the mounting interfaces
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbo.
Check the lubrication circuit, the oil supply and return lines, and ensure all pipes are clean d.
Check the intake and ensure that no foreign objects can reach the compressor wheel.
Carry out the priming procedure in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number marked on the original turbo d, the OEM and manufacturer part numbers, as well as the make, model, generation, body style, engine type, power output, production period and engine code. The same engine type may be fitted with several different turbochargers.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your original turbocharger d.