This hybrid turbocharger, designed for the Ford Ranger 2.8 D with a 130 hp engine, features internal modifications designed for to adapt its compression capacity and dair flow. Depending on the upgrade package selected, the modifications involve the MFS compressor wheel, the housings and, at the most advanced level, the turbine wheel.
It is designed to be fitted without any modifications to the vehicle, but to make full use of its performance characteristics, a corresponding engine upgrade and appropriate tuning of the boost management system are required.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor section in order dto adapt the air flow rate dwhilst maintaining a balanced configuration at high speed.
Stage 2
Compressor impeller: MFS high-flow oversized
d’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a reprofiled dintake housing. This modification is designed to increase the air displacement capacity dwithout compromising the engine’s final power output.
Stage 3
Compressor impeller: MFS high-flow oversized
dintake housing: Reprofiled for accommodate the new impeller oversized
Thrust bearing system: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
Stage 3 modifies the compressor and turbine sides. The final performance depends on the overall engine configuration, boost settings and operating conditions d.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate modified internal components. Depending on the upgrade stage, the modifications may involve the compressor wheel, the housings, the turbine wheel, the thrust bearing system and balancing.
The aim is dto adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its impeller: the geometry of the components and the overall coherence of the assembly determine its performance.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process alone does not guarantee an increase in airflow d. A standard MFS wheel may retain a geometry equivalent to that dof the original.
An MFS wheel Performance can be given a geometry adapted to the modification. On this product, the wheel shown is made of forged aluminium; it is lighter, larger and taller than the d’original; it is claimed for to allow for 15 per cent additional compression. The exact dimensions are not specified.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow can only be utilised properly with appropriate engine tuning.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and the arrangement of its blades influence the compressor’s aerodynamic behaviour.
Appropriate geometry can move more air dunder certain conditions. The result also depends on the casings, the turbine wheel, the boost pressure and the engine tuning. A larger wheel therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbo
The documented 360° thrust bearing helps to distribute the axial forces exerted on the rotating assembly. It helps the turbo adapt to the stresses of engine tuning without making it insensitive to assembly or lubrication faults.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses during operation.
Engine remapping and tuning
The engine mapping and boost pressure management must be adapted for to make the most of the hybrid turbo’s characteristics. The wastegate must be adjusted during the ECU reprogramming.
Depending on the level of tuning, the fuel injection system, exhaust system, intake air cooling d, clutch or gearbox may also require inspection or adjustment. The turbocharger alone does not guarantee a power increase.
Turbo specifications
OEM part numbers
79517
AR79517
EX79517
Manufacturer part numbers
724652-0001
724652-0007
724652-5001S
724652-5007S
Compatible vehicles and applications
Ford
Ranger 2,.8, D –130 hp
2.8 L diesel engine — from 2002, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: Hybrid Turbo
Turbo model: GT2256V
Engine: 2.8 D
displacement: 2.8 L
Fuel: Diesel
Power: 130 hp
Production period: From 2002
Engine code: Not specified
Fitting instructions
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d’installing the turbo. Check the lubrication circuit, the oil supply and return d’as well as the cleanliness of the pipes.
Check the intake for foreign objects. Prime the system in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further damage to the turbocharger.
How do you identify the correct turbo?
Check the part number marked on the original turbo dand compare it with the OEM and manufacturer part numbers in this data sheet. Also check the make, model, engine type 2.8 D, power output 130 hp and installation period.
An identical engine specification does not always guarantee compatibility: the generation, vehicle configuration and engine code must be taken into account where available.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your original turbo d.