This hybrid turbo is designed for Bmw 525D E60 and E61 fitted with the 2.5-litre engine D. Its design incorporates an MFS compressor wheel Performance high-throughput, a 360° bearing stop and high-speed balancing on a Cimat VSR bench.
Three levels of preparedness are documented. When choosing a conversion kit, you must take into account the engine configuration, the intended use and any necessary peripheral modifications.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS Performance high-capacity
Dimensions: 39.57 / 56.03 mm
Blade configuration: 11+0
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This system is based on an MFS compressor wheel Performance whose geometry is designed to adjust the flow rate d'air'. It retains its intended configuration for one Installation without modification of the vehicle, subject to a background check and appropriate adjustments.
Stage 2
Compressor wheel: MFS Performance high-capacity oversized
Dimensions: 47.50 / 60.01 mm
Blade configuration: 11+0
Carter d'Admission:' reprofiled for to receive the wheel oversized
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
The wheel oversized and the re-profiling of the casing d'admission requirements allow' d'adapt the passage' d'air with this geometry'. This change may affect the flow capacity and behaviour of the turbocharger; it must be accompanied by appropriate engine tuning.
Stage 2+
Compressor wheel: MFS Performance high-capacity oversized
Dimensions: 50.20 / 65.00 mm
Blade configuration: 11+0
Carter d'Admission:' reprofiled for to receive the wheel oversized
Bearing stop: 360°
Balancing: high speed at 150,000 rpm on a Cimat VSR test bench
This version uses the largest compressor wheel on record for this product, with a casing d're-profiled intake'. A larger wheel can move more d'air under certain conditions, but it can also affect the response time and the range d'optimal use'.
What is a hybrid turbo ?
A hybrid turbocharger is based on a turbocharger design that has been adapted to accommodate internal components or machining processes that differ from the standard configuration d'origin'. Depending on the modification, changes may relate to the compressor impeller, its dimensions, the geometry of the blades, the casings, the turbine impeller, the thrust bearing system or the balancing.
The aim is d'adjust the compression capacity and flow rate' d'air to meet the requirements of engine preparation'. A hybrid turbocharger is not defined solely by the appearance of its compressor wheel: consistency between the geometry, the housings, the rotor and the settings is essential.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This term describes a manufacturing process and does not, in itself, guarantee an increase in flow rate d'air'.
A standard MFS wheel can retain a geometry equivalent to that d'origin'. An MFS wheel Performance may, depending on its design, have a diameter, profile or blade configuration suited to the intended purpose.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air'. A higher flow rate can contribute to power output when the engine management system and peripheral equipment are correctly configured, although this alone does not guarantee a gain.
Why does the geometry of the blades affect the flow rate? d'air?' ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades influence the aerodynamic behaviour of the compressor. The right geometry can move more d'air within certain operating ranges'.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine tuning. A larger wheel therefore does not automatically guarantee better performance and may affect the turbo’s response time.
Reliability and balancing of the hybrid turbocharger
The 360° bearing stop documented for each stage helps to distribute the axial forces to which the rotor is subjected. It does not exempt d'proper lubrication, d'careful assembly and appropriate adjustments'.
The rotor is balanced at high speed – 150,000 rpm – on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not protect against contamination of the circuit d'oil, a fault' d'boots up incorrectly or is installed incorrectly'.
Engine remapping and tuning
It may be necessary to adjust the engine management system for make the most of the hybrid turbo’s features. Mapping, boost pressure and wastegate adjustment must be checked during installation and remapping.
Depending on the level of preparation: fuel injection, exhaust, air cooling d'The intake, clutch or gearbox may also need to be checked or adjusted'. The editing d'A hybrid turbo does not automatically guarantee a power boost without the right set-up'.
Turbo part numbers
OEM part numbers — Bmw
11657791758
7791709E
7791709G
7791709I
7791709K
7791758
7791758I
7791758K
Manufacturer’s part numbers
750080-0001
750080-0007
750080-0013
750080-0015
750080-0016
750080-0018
750080-5001S
750080-5007S
750080-5013S
750080-5015S
750080-5016S
750080-5018S
750080-1
750080-7
750080-13
750080-15
750080-16
750080-18
Compatible vehicles and assignments
Bmw
525D E60 / E61 — 163 hp
2.5-litre engine D — from 2003, end date unspecified
Engine code : not specified
525D E60 / E61 — 170 hp
2.5-litre engine D — from 2003, end date unspecified
Engine code : not specified
525D E60 / E61 — 177 hp
2.5-litre engine D — from 2003, end date unspecified
Engine code : not specified
Additional technical specifications
Product type: Hybrid Turbo
Installation: Plug-and-play, with no modifications to the vehicle required
Engine: 2.5 D
Documented power ratings: 163, 170 and 177 hp
Period covered: From 2003, end date unspecified
Engine code : Not specified
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Identify and rectify the cause of the previous fault before d'fit the turbo'. Check the lubrication circuit, the supply and the return d'the oil and the cleanliness of all the pipes'.
Check the intake and ensure there are no foreign objects present. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions.
The wastegate setting must be checked during installation and when adjusting the engine management system.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger d'origin and compare it with the OEM and manufacturer part numbers listed on this sheet'. Also check the make, model, generation, body style, engine type and power output in hp, the assembly period and the engine code, where available.
Having the same motor is not always enough to confirm compatibility, as there may be several different configurations.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d'origin' using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are unsure about which course to choose, please contact us before placing your order.