This hybrid turbocharger, designed for use in engines Renault 2.2 TD of 115 hp is available in various forms Stage 1, Stage 2 and Stage 2+. Designed for an installation plug & play, depending on the training course, it is fitted with a high-flow MFS compressor wheel, a 360° bearing retainer and high-speed balancing.
The documented assignments relate in particular to Renault Espace III, Grand Espace III, Laguna and Safrane. The benchmark for turbochargers dThe origin must always be checked before placing an order.
Available products — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: High-capacity MFS
Stop: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
This system is based on an MFS compressor wheel designed for adjust the flow rate d’air, whilst retaining the documented mechanical configuration of the Stage 1.
Stage 2
Compressor wheel: High-capacity MFS oversized
Carter d’Admission:’ Reprofiled for to receive the new wheel oversized
Stop: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 pairs a wheel oversized to re-profiling the casing d’admission’. This modification is designed to accommodate the new geometry correctly and to alter the range of movement dcompressor air.
Stage 2+
Compressor wheel: High-capacity MFS oversized
Carter d’Admission:’ Reprofiled for to receive the new wheel oversized
Stop: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
The available data indicate for the Stage 2+ the same list of documented changes as for the Stage 2. No other mechanical differences or performance figures are specified.
What is a hybrid turbo ?
A hybrid turbo is based on a specially adapted turbocharger design for to receive modified internal components. Depending on the specific configuration, modifications may relate to the compressor wheel, its dimensions and geometry, the casings, the turbine wheel, the thrust bearing system or the balancing process.
The aim is d’adjust the compression capacity and flow rate’ d’air to meet the requirements of engine preparation. A hybrid turbocharger is therefore not defined solely by the appearance of its compressor wheel, but by the coherence of the mechanical assembly as a whole.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This designation describes the manufacturing process and is not, on its own, sufficient to demonstrate an increase in flow rate dair.
A standard MFS wheel can retain a geometry close to its original shape. An MFS wheel Performance may be fitted with a blade profile, height, width or diameter suited to the intended application, provided that these modifications are documented. On this product, the wheel is described as being made of forged aluminium, and as being lighter, larger and taller than the one d’origin’. The data provided indicates an additional compression capacity of 15 per cent, although this does not automatically correspond to an equivalent increase in engine power.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more dair. Higher power output can only be utilised properly with appropriate engine tuning.
Why does the geometry of the blades affect the flow rate? d’air ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades influence the aerodynamic behaviour of the compressor and the volume d’the air it can displace under certain conditions’.
The result also depends on the compressor housing, the impeller and the turbine housing, the boost pressure and the engine management system. A larger wheel is not necessarily better: it can affect response time and range dGetting the most out of the turbo.
Reliability and balancing of the hybrid turbocharger
The 360° stop, as documented in the three training courses, helps to ensure a more even distribution of the axial forces acting on the rotating assembly. It must operate using clean oil that meets the required specifications.
Every preparation benefits from d’high-speed balancing at 150,000 rpm on a Cimat VSR test bench’. This procedure is designed to minimise vibrations and mechanical stresses on the rotor, but does not compensate for inadequate lubrication or incorrect installation.
Engine remapping and tuning
The farm dA hybrid turbo may require adjustments to the engine mapping and boost pressure control. Depending on the vehicle’s configuration, the fuel injection, exhaust and air cooling systems d’The intake, clutch or gearbox must also be checked and adjusted if necessary’.
The wastegate must be adjusted when the ECU is remapped. Fitting the turbo alone does not automatically result in an increase in usable power.
Turbo part numbers
OEM part numbers
7.700.101.141B
7700101141
7701471112
7711134199
Manufacturer’s part numbers
454164-0002
454164-0004
454164-5004S
GT1749S
Compatible vehicles and assignments
Renault
Espace III 2.2 TD — 115 hp
2.2 TD • From 1996, end date unspecified
Engine code : not specified
Large Espace III 2.2 TD — 115 hp
2.2 TD • From 1996, end date unspecified
Engine code : not specified
Laguna Nevada Phase 1 2.2 TD — 115 hp
2.2 TD • From 1996, end date unspecified
Engine code : not specified
Laguna Nevada Phase 2 2.2 TD — 115 hp
2.2 TD • From 1996, end date unspecified
Engine code : not specified
Laguna Phase 1 2.2 TD — 115 hp
2.2 TD • From 1996, end date unspecified
Engine code : not specified
Laguna Phase 2 2.2 TD — 115 hp
2.2 TD • From 1996, end date unspecified
Engine code : not specified
Safrane 2.2 TD — 115 hp
2.2 TD • From 1998, end date unspecified
Engine code : not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: Renault 2.2 TD
displacement : 2.2 l
Power : 115 hp
Turbo model: GT1749S
Editing: Plug and play, no modifications required d’installation’
Engine code : Not specified
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Identify and rectify the cause of the previous fault before carrying out any installation work. Check the lubrication circuit, the supply and the return doil, as well as ensuring that all ducts are clean.
Check the intake and ensure there are no foreign objects present. Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions.
If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger d…the original and compare it with the OEM and manufacturer’s specifications in this data sheet. Also check the make, model, generation, body style and engine type 2.2 TD, the power of 115 hp, theYear the mounting code and the engine code, where available.
Having the same engine is not always enough to confirm compatibility, as several different configurations may coexist depending on the vehicle version.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d’origin’ using the references given in this fact sheet. Having the same motor does not always guarantee compatibility.
If you are in any doubt, please contact our team with the reference number shown on your turbocharger.