This hybrid turbocharger for for the 3.0 DCI engine with 175 hp is based on the plug & play architecture and features internal modifications tailored to the chosen tuning level. The three documented tuning stages utilise a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing on a Cimat VSR test bench.
The part numbers for the original dturbocharger must be checked before placing any order, as the specific vehicle application and engine code are not documented in the available information.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification primarily affects the compressor impeller in order dto adjust the compression capacity and the dair flow rate. It retains a documented external dconfigurationInstallation without modification.
Stage 2
Compressor impeller: MFS high-flow oversized
d’inlet housing: Reprofiled for to accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The Stage 2 combines a oversized compressor impeller with a reprofiled dintake housing. This modification is designed to correctly accommodate the new geometry and enable a higher air flow rate dunder appropriate operating conditions.
Stage 3
Compressor impeller: MFS high-flow oversized
dintake housing: Reprofiled for accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This version adds a turbine impeller oversized and a reprofiled turbine housing. The assembly can alter the flow capacity and response time of the turbocharger; its operation depends on the engine’s overall configuration.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate internal components that differ from the original configuration d. Depending on the stage, modifications may involve the compressor wheel, housings, turbine wheel, thrust bearing and balancing.
The aim is dto adapt the compression capacity and the air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry of the wheels, the machining of the housings and the overall coherence of the assembly are crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process and does not, on its own, guarantee an increase in air flow d.
A standard MFS impeller may retain a geometry equivalent to that of the original d. An MFS ‘ Performance ’ impeller may feature a diameter, profile or blade geometry tailored to the tuning objective. On this product, the wheel shown is made of forged aluminium, lighter, larger and taller than the original one d; the data provided indicates an additional 15 per cent compression.
A standard MFS impeller can be just as shiny as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow can contribute to power output when the engine tuning is correctly adapted.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air destined for the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour and the amount dof air it can move.
The result also depends on the housings, the turbine wheel, the boost pressure and the engine management system. A larger wheel therefore does not automatically guarantee better performance and may alter the response time as well as the range d’of optimal operation.
Reliability and balancing of the hybrid turbo
The documented 360° thrust bearing helps to distribute the axial forces exerted on the rotating assembly. It does not replace d’proper lubrication or d’correct installation.
Each unit undergo dhigh-speed balancing at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses on the rotor, though it cannot compensate for any faults din installation, lubrication or din the oil supply.
Engine remapping and preparation
Appropriate engine management is required for to make the most of the hybrid turbo’s characteristics. Map settings, boost pressure and wastegate adjustment must be checked when remapping the ECU.
Depending on the level of tuning, the fuel injection, exhaust, cooling, intake, as well as the clutch or gearbox may require checking or adjustment. Fitting this turbo alone does not guarantee a power increase.
Turbo part numbers
OEM part numbers
8972409266
8972409267
7701474093
Manufacturer part numbers
714306-0005
714306-0006
714306-5005S
714306-5006S
Compatible vehicles and applications
Specific vehicle applications are not documented. It is essential to check the original turbo dpart numbers, engine type, power output and engine code before ordering.
Additional technical specifications
Product type: Hybrid Turbo
Engine: 3.0 DCI
Power: 175 hp
Turbo model: GT2559V
Part number: 714306
Installation: Configuration plug & play, documented
Engine code: Not specified
Fitting period: Not specified
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d’installing the turbocharger. Check the lubrication circuit, the oil supply and return d’as well as the cleanliness of all pipes.
Check the intake for foreign objects. Prime the system in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
A lubrication fault that is not rectified may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number engraved or marked on the original turbo d, then compare it with the OEM and manufacturer part numbers in this data sheet.. Also check the make, model, generation, body style, engine type 3.0 DCI, power output 175 hp, theYear and the engine code.. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number of your original turbo d.