This hybrid turbo for, with a 2.2 CDI engine, is designed for for the Mercedes-Benz Sprinter II models with 129 and 150 hp, listed in this data sheet.. Depending on the upgrade package chosen, the kit combines a high-flow MFS compressor wheel, a 360° bearing stop and appropriate internal modifications.
The configuration is advertised as plug & play, with a Installation without modification on compatible applications. The available tuning options allow you to choose a level of modification consistent with your engine project, without prejudging the final power output.
Available tuning packages — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Bearing retainer: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification is carried out on the compressor impeller in order d to adapt the compression capacity and the air flow rate d. The 360° thrust bearing helps to distribute the axial forces borne by the rotating assembly more evenly.
Stage 2
Compressor wheel: MFS high-flow oversized
d' intake housing: re-profiled for accommodate the new impeller oversized
Bearing thrust ring: 360°
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
Stage 2 combines a oversized compressor impeller with a reprofiled housing d'admission. This modification is designed to ensure the new impeller fits correctly and to improve the compressor’s aerodynamic performance.
Stage 3
Compressor impeller: MFS high-flow oversized
Casing d Inlet: re-profiled for to accommodate the new impeller oversized
Bearing thrust ring: 360°
Turbine impeller: high flow oversized
Turbine casing: re-profiled for ly to accommodate the new impeller oversized
Balancing: high-speed at 150,000 rpm on a Cimat VSR test bench
This modification alters the compressor and turbine sides. Both housings are re-profiled for to accommodate the corresponding oversized impellers. Its performance depends on the overall engine configuration and the turbocharging management system.
What is a hybrid turbo?
A hybrid turbo utilises a turbocharger architecture adapted for to accommodate internal modifications. Depending on the stage of modification, these may involve the compressor wheel, its dimensions, the housings, the turbine wheel, the thrust bearing or the balancing.
The aim is d to adapt the compression capacity and air flow d to the requirements d of an engine upgrade. A hybrid turbo is therefore not defined solely by the appearance of its compressor wheel: the geometry, the machining of the housings and the overall coherence of the unit are crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process, but does not in itself guarantee an increase in air flow d.
A standard MFS impeller may retain a geometry equivalent to that of the original d'original. A ‘ Performance ’ MFS impeller may feature a profile, dimensions or blade configuration tailored to the tuning objective. For this product, the wheel is described as a forged aluminium wheel, which is lighter, larger and taller than the original d, with a claimed 15 per cent increase in compression.
A standard MFS impeller can be just as effective as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A higher airflow rate can contribute to power output with appropriate engine tuning, though it does not in itself guarantee a specific result.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air intended for the engine. Its diameter, profile, height, width and the arrangement of its blades directly influence the aerodynamic behaviour of the compressor.
A suitably designed geometry can move more air d under certain conditions. The result also depends on the casings, the turbine wheel, the boost pressure and the engine mapping. A larger wheel does not automatically guarantee better performance and may alter the response time as well as the range d of optimal operation.
Reliability and balancing of the hybrid turbo
The 360° bearing stop, featured on all three stages, distributes axial forces across the entire surface. It contributes to the mechanical integrity of the assembly without making the turbocharger insensitive to poor lubrication or incorrect fitting.
Each stage undergo d high-speed balancing at 150,000 rpm on a Cimat VSR test bench. This process aims to minimise vibrations and stresses on the rotor during operation.
Engine remapping and tuning
Appropriate engine management is necessary for to make full use of the hybrid turbo’s characteristics. The wastegate must be adjusted during the ECU remapping.
Depending on the level of tuning, it is also advisable to check or d'adjust the mapping, fuel injection, exhaust system, cooling, boost pressure and, if necessary, the transmission. Fitting d'a hybrid turbo does not automatically guarantee a power gain without a coherent configuration.
Turbo specifications
OEM part numbers
6460900280
a6460900280
Manufacturer part numbers
54399700049
54399800049
54399880049
54399900049
KP39
KP39-049
Compatible vehicles and assignments
Mercedes-Benz
Sprinter II (213, 906) — 129 hp
2.2 CDI — from 2006, end date unspecified
Engine code : unspecified
Sprinter II (313, 906) — 129 hp
2.2 CDI — from 2006, end date unspecified
Engine code : unspecified
Sprinter II (215, 906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : unspecified
Sprinter II (315, 906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : unspecified
Sprinter II (415, 906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : unspecified
Sprinter II (515, 906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : unspecified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.2 CDI
displacement: 2.2 l
Power: 129 / 150 hp
Documented installation period: from 2006
Configuration: installation plug & play -specified, without modification d' installation
Fitting advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Before installation, identify and rectify the cause of the previous failure. Check the lubrication circuit, the oil supply and return d as well as the cleanliness of the pipes.
Check the inlet for foreign objects. Prime the system in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further damage to the turbocharger.
How do you identify the correct turbo?
Check the part number engraved or marked on the original turbo d, then compare it with the OEM and manufacturer part numbers in this data sheet.. Also check the make, model, generation, version, engine type, power output at hp, theYear and the engine code where available.
A single engine type may be fitted with several different turbocharger set-ups. Checking the part numbers therefore remains the most reliable way d to identify the correct configuration.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet.. An identical engine does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your original turbocharger d.