This hybrid turbo plug & play is designed for engines Mercedes-Benz Sprinter II (906) 2.2 CDI between 109 and 150 hp as set out in this fact sheet. Depending on the package chosen, these set-ups combine a high-flow MFS compressor wheel, a 360° stop and appropriate internal modifications.
The available configurations allow you to select a level of tuning that is consistent with the engine project, without specifying a predefined final power output. The benchmark for turbochargers d'The origin must be verified before any order is placed'.
Available products — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: High-capacity MFS
Stop system: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
This product acts primarily on the compressor section in order to d'adjust the travel capacity' d'turbo air'. The 360° stop helps to ensure a more even distribution of axial forces.
Stage 2
Compressor wheel: High-capacity MFS oversized
Carter d'Admission:' Reprofiled for to receive the new wheel oversized
Stop system: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
The Stage 2 incorporates a compressor wheel oversized to a casing d're-profiled intake'. This modification is designed to accommodate the new wheel geometry and to adjust the flow rate d'available air depending on operating conditions'.
Stage 3
Compressor wheel: High-capacity MFS oversized
Carter d'Admission:' Reprofiled for to receive the new wheel oversized
Stop system: 360° thrust bearing
Turbine wheel: High flow rate oversized
Turbine casing: Reprofiled for to receive the new wheel oversized
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
This configuration alters the compressor and turbine sections. The performance achieved depends on the engine setup, boost pressure and the settings chosen; a larger wheel is therefore not automatically better suited to all uses.
What is a hybrid turbo ?
A hybrid turbo is based on a specially adapted turbocharger design for to receive modified internal components. Depending on the course, the preparation may involve the compressor wheel, the casings, the turbine wheel, the thrust bearing or balancing.
The aim is d'adjust the compression capacity and flow rate' d'air'. However, a hybrid turbo is not defined solely by the appearance of its impeller: the geometry, dimensions, machining of the housings and the overall balance are all crucial factors.
MFS compressor wheel: standard or Performance ? ?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This manufacturing process does not, on its own, guarantee an increase in throughput d'air'. A standard MFS wheel can retain a geometry equivalent to that d'origin'.
An MFS wheel Performance can be designed with a geometry suited to the project: profile, height, width, diameter or blade arrangement. In this product, the diagrams show a high-flow MFS wheel, oversized for Stages 2 and 3.
A standard MFS wheel can be just as shiny as an MFS wheel Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air'. A higher flow rate can help to generate more power when the engine has been suitably tuned, although this alone does not guarantee results.
Why does the geometry of the blades affect the flow rate? d'air?' ?
The compressor wheel draws in and then compresses the air fed to the engine. Its diameter, profile, height, width and the arrangement of its blades all influence its aerodynamic behaviour. The result also depends on the casings, the turbine wheel, the boost pressure and the engine management system. An increase in size may also affect the response time and the range d'optimal use'.
Reliability and balancing of the hybrid turbocharger
The 360° bearing stop, which is fitted to all three stages, distributes the axial forces over a wide surface area. It must, however, operate with adequate lubrication and under the specified conditions for the preparation.
The rotor is balanced at high speed – 150,000 rpm – on a Cimat VSR test bench, in order to minimise vibrations and mechanical stresses. This balancing does not compensate for incorrect installation, contamination of the system or inadequate lubrication.
Engine remapping and tuning
The engine management system needs to be adjusted for make the most of the hybrid turbo’s features. Mapping, boost pressure and wastegate settings must be checked during remapping. According to the project, the fuel injection, exhaust, cooling, intake and transmission systems may also require checking or adjustment.
Turbo part numbers
OEM part numbers
6460900480
A6460900480
A6460902080
A6450902080
6460902080
6450902080
Manufacturer’s part numbers
759688-5002S
759688-5003S
759688-5005S
759688-5007S
759688-0002
759688-0003
759688-0005
759688-0007
759688-2
759688-3
759688-5
759688-7
Compatible vehicles and assignments
Mercedes-Benz
Sprinter II 211 (906) — 109 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 215 (906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 311 (906) — 109 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 315 (906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 411 (906) — 109 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 415 (906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 511 (906) — 109 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Sprinter II 515 (906) — 150 hp
2.2 CDI — from 2006, end date unspecified
Engine code : not specified
Additional technical specifications
Product type: Hybrid Turbo
Turbo model: GTB1749VK
Engine: 2.2 CDI
Documented power ratings: 109 and 150 hp
Set-up period: From 2006, end date unspecified
Editing: Plug and play, no modifications required d'documented installation'
Assembly instructions
⚠️ WARNING — IMPORTANT BEFORE ASSEMBLY
Identify and rectify the cause of the previous fault. Check the lubrication circuit, as well as the supply and return lines d'oil'. Check that the ducts and the intake are clean and free from foreign objects.
Carry out the priming in accordance with the relevant guidelines and follow the manufacturer’s instructions. If a lubrication fault is not rectified, it may lead to the turbocharger failing again.
How do you choose the right turbo ?
Check the part number marked on the turbocharger d'origin, OEM and manufacturer part numbers, as well as the make, model, generation, engine type, power output, theYear installation and engine code. A single motor can be fitted with several different configurations.
⚠️ Check your turbo’s part numbers
Before placing your order, Compare the part number on your turbocharger d'origin' using the references given in this fact sheet. Having the same motor does not always guarantee compatibility. If you are in any doubt, please contact us before confirming your choice.