This hybrid turbocharger, designed for a 2.0 L engine producing 177, hp, combines a documented installation plug & play with internal modifications tailored to the chosen tuning level. The three available tuning stages incorporate a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing.
Higher-level packages add a compressor wheel oversized, a re-profiled intake casing d and, for for Stage 3, modifications to the turbine side.. Compatibility must be checked against part numbers 14412AA370 and 49135-04700.
Available kits — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrustbearing: 360° thrust bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
This configuration primarily affects the compressor side in order d to adjust the compression capacity and d the air flow. The 360° thrust bearing helps to distribute axial forces under the intended operating conditions.
Stage 2
Compressor impeller: MFS high-flow oversized
d ’ intake housing: Reprofiled for accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
Reprofiling the housing allows d to fit the compressor wheel oversized. This configuration can move more d air under certain conditions, but its performance also depends on the engine management system and the overall mechanical setup.
Stage 3
Compressor wheel: MFS high-flow oversized
d'intake housing: Reprofiled for to accommodate the new impeller oversized
Thrustbearing: 360° thrust bearing
Turbine impeller: High-flow oversized
Turbine housing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This modification is carried out on both the compressor and turbine sides. The sizing of the impellers and the re-profiling of the housings alter the flow conditions and may also influence the turbocharger’s response time.
What is a hybrid turbo?
A hybrid turbo retains an architecture suited to the intended installation whilst incorporating internal modifications. Depending on the modification package, these may involve the compressor impeller, the housings, the turbine impeller, the thrust bearing system and the balancing.
The aim is d to adapt the compression capacity and air flow d to the requirements d of an engine upgrade. However, a hybrid turbo is not defined solely by the appearance of its compressor wheel: the geometry of the wheels, their combination with the housings and the quality of the balancing are crucial.
MFS compressor wheel: standard or ‘ Performance ’?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. The wheel documented here is made from forged aluminium and features a design that is lighter, larger and taller than the d original. The available data indicates an additional 15 per cent boost capacity.
A standard MFS wheel can retain a geometry equivalent to the original. Conversely, an MFS wheel Performance can be given a geometry tailored to the tuning objective, such as a different blade profile, height, width or diameter, where these elements are specified.
A standard MFS impeller can be just as polished as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d air. A higher airflow rate can contribute to power output with appropriate engine tuning, though it does not, on its own, guarantee a specific result.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, the blade profile, their height, width and arrangement all influence the compressor’s aerodynamic behaviour.
A suitably designed geometry can move more air d within certain operating ranges. The result also depends on the casings, the turbine wheel, the boost pressure and the engine tuning. A larger wheel therefore does not automatically guarantee a better result and may alter the response time.
Reliability and balancing of the hybrid turbo
The 360° bearing stop, featured on all three stages, distributes axial forces over a wide surface area. It contributes to the mechanical integrity of the assembly without making the turbo immune to installation or lubrication faults.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR test bench. This process aims to minimise vibrations and mechanical stresses during rotation.
Engine remapping and preparation
To make the most of the characteristics d of a hybrid turbo, the engine management system must be adapted. The mapping, boost pressure and wastegate settings must be checked when remapping the ECU.
Depending on the level of tuning, the injection d, exhaust d and cooling systems may also require checking or adjustment. The clutch, gearbox and other vehicle components must remain compatible with the chosen configuration.
Turbo specifications
OEM part number
14412AA370
Manufacturer reference
49135-04700
Compatible vehicles and applications
Detailed vehicle specifications are not provided. Check compatibility using the original turbo part numbers d, the engine type 2.0 L and the power output of 177 hp.
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.0 L
Power: 177 hp
Installation: Plug & play, no documented modifications required for for fitting
Engine code and installation time: Not specified
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbo.
dCheck the lubrication circuit, the oil supply and return lines, and ensure the pipes are clean. Also check the intake for any foreign objects.
Carry out the priming procedure in accordance with the applicable recommendations and follow the vehicle manufacturer’s instructions.
Failure to rectify a lubrication fault may result in the turbocharger failing again.
How do you identify the correct turbo?
Check the part number engraved or marked on the original turbo d, then compare it with the OEM and manufacturer part numbers in this data sheet.. Also check the make, model, generation, body style, engine type, power output at hp, production period and engine code where available.
An identical engine specification does not always guarantee compatibility, as there may be several different set-ups for for the same version.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the full part number of your turbocharger.