This hybrid turbocharger is designed for for the 2.7 TDI engines documented at.. Its configuration combines a high-flow MFS compressor wheel, a 360° bearing stop and high-speed balancing in order d to adapt the compression capacity and d air flow rate according to the selected stage.
Installation is designed for a ‘ plug & play ’ configuration, without any changes to the layout. The main applications are the compatible Maverick Ford and Nissan Terrano II models.
Available configurations — Stage 1, Stage 2 and Stage 2+
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR bench
This configuration utilises an MFS compressor impeller suitable for a higher air flow rate d, without any documented housing modifications for this stage.
Stage 2
Compressor impeller: High-flow MFS oversized
d intake casing: Reprofiled for accommodate the new impeller oversized
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The reprofiling of the casing allows for the integration of the oversized impeller. This modification may alter the air displacement capacity d and the compressor’s performance depending on the associated engine tuning.
Stage 2+
Compressor impeller: MFS high-flow oversized
d intake housing: Reprofiled for to accommodate the new impeller oversized
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This specification incorporates the mechanical characteristics of the. detailed above. The choice of tuning package must take into account the engine’s configuration, its intended use and the planned settings.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture adapted for to accommodate modified internal components. Depending on the modification, changes may relate to the compressor wheel, its dimensions, the geometry of the blades, the machining of the housings, the thrust bearing or the balancing.
The aim is d to adapt the compression capacity and air flow rate d. However, a hybrid turbo is not defined solely by the appearance of its impeller: the entire mechanical configuration and its suitability for the engine must be taken into account.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’, meaning a wheel machined from a solid block. This technology describes the manufacturing process and does not, on its own, guarantee an increase in airflow d. A standard MFS wheel can retain a geometry equivalent to that d of the original.
An MFS wheel Performance can be given a geometry tailored to the intended purpose. For this product, a forged aluminium wheel – lighter, larger and taller than the d original – is documented, with a claimed 15 per cent higher compression capacity.
A standard MFS impeller can perform just as well as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d'air. A higher flow rate can contribute to an increase in power when the engine tuning is correctly adapted, though it does not in itself guarantee results.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour. A suitable geometry can move more d'air under certain conditions, but the result also depends on the casings, the turbine, the boost pressure and the engine management system. A larger impeller therefore does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbocharger
The documented 360° thrust bearing distributes axial forces over a wide surface area. Balancing the rotor at 150,000 rpm on a Cimat VSR test bench helps to limit vibrations and mechanical stresses at high speeds. However, these procedures do not compensate for incorrect installation, nor a lack of lubrication.
Engine remapping and preparation
To make the most of the characteristics d of a hybrid turbocharger, it may be necessary to adjust the engine mapping and boost pressure management. The fuel injection, exhaust, intake air cooling d, the clutch or the transmission must also be checked depending on the level of tuning.. The wastegate must be adjusted when remapping the ECU.. The configuration must be carried out by a qualified professional.
Turbo specifications
OEM part numbers
144117F400
144117F0400
Manufacturer part numbers
452162-0001
452162-1
452162-5001S
Compatible vehicles and applications
Ford
Maverick 2.7 TDI –123 hp
Engine variants 2.7 TDI — from 1997, end date unspecified
Engine code: not specified
Maverick 2.7 TDI –125 hp
Engine variants., 7 TDI — from 1997, end date unspecified
Engine code: not specified
Nissan
Terrano II 2.7 TDI — 123 hp
Engine variants: 2-., 7- TDI — from 1996, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.7 TDI
displacement: 2-.7 litres
Fuel: Diesel
Power: 100 / 125 hp depending on product designation; specifications documented for 123 and 125 hp
Installation: Plug & play, no modification to the layout required
Engine code: Not specified
Installation advice
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault before d installing the turbo. Check the lubrication circuit, as well as the oil supply and return d.
Check that the pipes and the inlet are clean and free from foreign objects. Carry out the priming procedure in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further turbocharger failure.
How do you identify the correct turbo?
Check the part number marked on the original turbo d, then compare the OEM and manufacturer part numbers.. Also check the make, model, generation, engine type, power output at hp, theYear and the engine code where available.. An identical engine type does not always guarantee compatibility.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If you are unsure about the identification or fitment, please contact us with the full part number of your original turbo d.