This hybrid turbo, designed for the 2., 5 DCI and 2.5 DTI engines with 135 hp, undergoes internal modification to adjust the compression ratio and air flow d. Depending on the upgrade package chosen, the modifications involve the MFS compressor wheel, the housings, the turbine impeller, the thrust bearing and the rotor balancing.
Documented applications include, in particular, the Nissan Primastar, Opel Vivaro, Renault Master 2 Phase 2 and Renault Trafic 2.
Available preparations — Stage 1, Stage 2 and Stage 3
Stage 1
Compressor wheel: MFS high-flow
Thrust bearing: 360° bearing
Balancing: High speed at 150,000 rpm on a Cimat VSR test bench
This modification acts on the compressor impeller to dadapt the flow rate dto the air, whilst retaining a configuration designed for to Installation without modification the vehicle’s assembly.
Stage 2
Compressor wheel: MFS high-flow oversized
Intake housing d: Reprofiled for accommodate the new impeller oversized
Thrust bearing: 360° bearing
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
The oversized impeller and the re-profiling of the intake housing denable dthe airflow to be adapted to this new geometry. The final performance also depends on the engine management system and the vehicle’s other components.
Stage 3
Compressor wheel: MFS high-flow oversized
Intake housing d: Reprofiled for accommodate the new impeller oversized
Thrust bearing: 360° bearing
Turbine impeller: High-flow oversized
Turbine casing: Reprofiled for ly to accommodate the new impeller oversized
Balancing: High-speed balancing at 150,000 rpm on a Cimat VSR test bench
This configuration combines modifications to both the compressor and turbine sides. Resizing the impellers and re-profiling the housings can alter the available flow rate as well as the response time; the result depends on the overall set-up.
What is a hybrid turbo?
A hybrid turbo is based on a turbocharger architecture designed for accommodate internal components that differ from the original dconfiguration. Depending on the stage, the modification may involve the compressor wheel, the dimensions of the wheels, the housings, the turbine wheel, the thrust bearing or the balancing.
The aim is dto adapt the compression capacity and air flow dto the requirements of the engine tuning. A hybrid turbo is therefore not defined solely by the appearance of its compressor wheel.
MFS compressor wheel: standard or Performance?
MFS stands for ‘Milled From Solid’ and refers to a wheel machined from a solid block. This manufacturing process does not, on its own, guarantee an increase in air flow d. A standard MFS wheel may retain a geometry equivalent to that dof the original.
An MFS impeller Performance can be designed with a geometry tailored to the specific application, particularly in terms of its profile or dimensions. A standard MFS impeller can be just as polished as an MFS impeller Performance. It is not its appearance that determines its performance, but its geometry and its ability to move more d’air. A higher airflow rate can contribute to power output with appropriate engine tuning, though it does not, on its own, guarantee a specific result.
Why does the geometry of the blades influence the air flow rate d?
The compressor impeller draws in and then compresses the air sent to the engine. Its diameter, profile, height, width and blade arrangement influence its aerodynamic behaviour. A suitable geometry can move more dair under certain conditions, but the result also depends on the casings, the turbine, the boost pressure and the engine management system. A larger impeller does not automatically guarantee better performance and may alter the response time.
Reliability and balancing of the hybrid turbo
The 360° thrust bearing, documented at each stage, distributes axial forces around the shaft. It helps the bearing adapt to operating stresses, without making the turbocharger immune to faults in assembly or lubrication.
The rotor is balanced at high speed, up to 150,000 rpm, on a Cimat VSR. test bench. This process aims to minimise vibrations and mechanical stresses on the rotor.
Engine remapping and preparation
The engine mapping must be adapted for to make full use of the hybrid turbo’s characteristics. Pressure management and wastegate adjustment must be carried out during remapping. Depending on the level of tuning, the fuel injection, exhaust system, cooling system, intake and transmission may also need to be checked or adjusted. The turbo alone does not guarantee a power gain.
Turbo specifications
OEM part number
8200184484
Manufacturer’s part numbers
714652-0002
714652-0004
714652-0005
714652-0006
714652-2
714652-4
714652-5
714652-6
Compatible vehicles and applications
Nissan
Primastar — 135 hp2.5 DCI — from 2002, end date unspecified
Engine code: not specified
Opel
Vivaro — 135 hp2,., 5 DTI — from 2001, end date unspecified
Engine code: not specified
Renault
Master 2 Phase 2 — 135 hp2.5 DCI — from 2003, end date unspecified
Engine code: not specified
Trafic 2 — 135 hp2.5 DCI — from 2001, end date unspecified
Engine code: not specified
Additional technical specifications
Product type: Hybrid Turbo
Engine: 2.5 DCI / 2.5 DTI
Power: 135 hp
Installation: No modifications to the vehicle’s mounting required
Fitting instructions
⚠️ WARNING — IMPORTANT BEFORE INSTALLATION
Identify and rectify the cause of the previous fault. Check the lubrication circuit, the oil supply and return das well as the cleanliness of the pipes.
Check the intake for any foreign objects. Carry out the priming procedure in accordance with the applicable recommendations and follow the manufacturer’s instructions.
A lubrication fault that is not rectified may lead to further damage to the turbocharger.
How do you identify the correct turbo?
Check the part number marked on the original turbo dand compare it with the OEM and manufacturer part numbers in this datasheet. Also check the make, model, generation, engine type, power output, mountingYear and, where available, the engine code.
⚠️ Check your turbo’s part numbers
Before ordering, compare the part number marked on your original turbo d with the part numbers listed in this data sheet. An identical engine specification does not always guarantee compatibility.
If in doubt, please contact us with the part number clearly visible on your turbocharger.